Boston Tech BE108 Paraffin Wax Bath

Introduction

The Boston Tech BE108 paraffin wax bath is a fast and safe heating device designed to soften skin and relieve joint pain. It is suitable for both cosmetic and therapeutic use, offering benefits for muscle pain, arthritis, and general skin revitalization. This manual provides essential instructions for the safe and effective use of your paraffin wax bath.

Important Safety Instructions

• Read all instructions before using the appliance.
• Do not immerse the appliance in water or other liquids.
• Always unplug the appliance from the power outlet immediately after use and before cleaning.
• Do not operate the appliance with a damaged cord or plug, or if it malfunctions or has been damaged in any manner.
• Keep the cord away from heated surfaces.
• Do not use outdoors.
• Always ensure the appliance is placed on a stable, heat-resistant surface.
• This appliance includes an overheat protection system and an insulating grid for safe operation.
• Do not touch the hot wax directly. Always check the temperature before use.
• Keep out of reach of children.

Package Contents

Your Boston Tech BE108 Paraffin Wax Bath package includes the following items:

• 1 x Boston Tech BE108 Paraffin Wax Bath Unit
• 2 x Paraffin Wax Blocks (450g each)
• 1 x Insulating Grid
• 2 x Thermal Gloves
• 100 x Plastic Gloves
• 1 x Brush
• 1 x User Manual

Product Overview

The Boston Tech BE108 features a robust design with high-quality ABS and heat-resistant aluminum. It has a compact and elegant form factor, making it easy to clean and suitable for various environments.

Control Panel

The control panel allows for precise temperature regulation and mode selection.

• Temperature Regulation Buttons: Use these to adjust the desired wax temperature between 30°C and 85°C.
• On/Off Button: Powers the unit on or off.
• Mode Switch: Selects different operating modes (if applicable).
• LCD Screen: Displays the current temperature.

Setup

1. Placement: Place the paraffin wax bath on a flat, stable, and heat-resistant surface. Ensure there is adequate ventilation around the unit.
2. Insert Grid: Place the insulating grid at the bottom of the wax bath. This prevents direct contact between the heating element and the user's skin.
3. Add Wax: Open the paraffin wax blocks and place them into the bath. The unit has a 5-liter capacity. Ensure the wax level is between the minimum and maximum fill lines.
4. Power On: Plug the power cord into a suitable electrical outlet. Press the On/Off button to turn on the unit.
5. Set Temperature: Use the temperature regulation buttons to set the desired melting temperature. For initial melting, a higher temperature (e.g., 70-80°C) can be used to speed up the process.
6. Melt Wax: Allow approximately 40 minutes for the wax to fully melt. The LCD screen will display the current temperature. Once melted, adjust the temperature to a comfortable and safe level for skin application (typically between 45-55°C).

Operating Instructions

Paraffin Treatment for Hands, Feet, or Elbows

1. Preparation: Ensure the area to be treated (hands, feet, or elbows) is clean and dry. Remove any jewelry.
2. Temperature Check: Before dipping, test a small amount of wax on your wrist to ensure the temperature is comfortable and not too hot. The recommended temperature for application is typically between 45-55°C.
3. First Dip: Slowly dip your hand, foot, or elbow into the melted paraffin wax. Immediately remove it, allowing the wax to solidify slightly (a few seconds).
4. Repeat Dips: Repeat the dipping process 3-5 times, or until a thick, even layer of wax has formed.
5. Covering: Immediately after the final dip, cover the treated area with a plastic glove, followed by a thermal glove. This helps retain heat and maximize the therapeutic effect.
6. Relaxation: Keep the wax on for 10-15 minutes. During this time, the heat will penetrate, providing relief and hydrating the skin.
7. Removal: Gently peel off the solidified wax. The wax should come off easily, taking dead skin cells with it. Discard the used wax.

Maintenance and Cleaning

1. Cool Down: After each use, turn off the unit and unplug it from the power outlet. Allow the wax to cool and solidify completely.
2. Remove Wax: Once the wax has solidified, it can often be removed as a single block. If necessary, gently scrape the sides with a non-abrasive tool to loosen it.
3. Clean Interior: Use a soft, damp cloth to wipe the interior of the bath. Do not use abrasive cleaners or solvents, as these can damage the surface.
4. Clean Exterior: Wipe the exterior of the unit with a soft, dry cloth.
5. Storage: Store the appliance in a cool, dry place when not in use.

Troubleshooting

• Wax not melting: Ensure the unit is properly plugged in and turned on. Check that the temperature setting is high enough for melting (e.g., 70-85°C). Allow sufficient time for the wax to melt (approx. 40 minutes).
• Wax too hot/cold: Adjust the temperature using the control panel buttons. Allow a few minutes for the wax to reach the new temperature. Always test the wax temperature before application.
• Skin irritation: If you experience any skin irritation, redness, or discomfort, discontinue use immediately. Consult a healthcare professional if symptoms persist.
• Unit not turning on: Check the power connection and ensure the outlet is functional. If the issue persists, contact customer support.

Specifications

Warranty and Support

The Boston Tech BE108 Paraffin Wax Bath comes with a 3-year warranty. For any technical assistance, product inquiries, or warranty claims, please contact Boston Tech official technical service in your region. Refer to the contact information provided on the product packaging or the official Boston Tech website.