Introduction
Thank you for choosing the TEEM Adjustable Clamp Desk Lamp. This manual provides essential information for the safe and efficient use of your new lamp. Please read these instructions carefully before installation and operation, and retain them for future reference.
Safety Information
- Ensure the power supply is disconnected before installation, cleaning, or bulb replacement.
- Use only E26 base bulbs with a maximum wattage of 60W (LED or incandescent). Exceeding this limit may cause overheating or damage.
- Do not operate the lamp with a damaged cord or plug.
- Keep the lamp away from water or damp environments.
- Ensure the clamp is securely fastened to a stable surface to prevent the lamp from falling.
Package Contents
Please verify that all components are present before beginning assembly:
- Lamp Unit with Swing Arm and Shade
- Desk Clamp Base
- Round Desktop Base (Optional, may be included depending on package)
- Power Cord with On/Off Switch
Setup Instructions
Follow these steps to assemble and set up your TEEM Desk Lamp:
- Choose Your Mounting Option: Decide whether to use the clamp base for space-saving attachment to a desk edge or the round desktop base for freestanding placement.
- Assemble the Lamp Arm: Insert the bottom pin of the lamp arm into the designated hole on your chosen base (either the clamp or the round desktop base). Ensure it is firmly seated.
Figure 1: Lamp arm assembly into the round base (left) or clamp base (right).
- Secure the Lamp (if using clamp): If using the clamp base, attach it to the edge of your desk or workbench. Tighten the screw mechanism until the clamp is firmly secured and the lamp is stable.
Figure 2: The TEEM desk lamp securely clamped to a desk surface.
- Place the Lamp (if using round base): If using the round desktop base, place the lamp on a flat, stable surface.
Figure 3: The TEEM desk lamp positioned on a desk using its round desktop base.
- Install the Bulb: Carefully screw an E26 base bulb (not included) into the lamp socket. Ensure the bulb does not exceed 60W.
- Connect to Power: Plug the power cord into a standard electrical outlet.
Operating Instructions
Your TEEM Desk Lamp is designed for flexible and convenient lighting:
- Power On/Off: Use the in-line switch located on the power cord to turn the lamp on or off.
- Adjusting the Swing Arm: The lamp features a multi-joint swing arm (22 cm + 22 cm / 8.7 in + 8.7 in) that allows for extensive reach and positioning. Gently move the arm to direct light as needed. The springs provide balance and hold the arm in place.
- Rotating the Shade: The lamp head can rotate 360 degrees. Adjust the shade to focus light precisely on your workspace and minimize glare.
Figure 4: The TEEM desk lamp providing illumination over a workspace.
Figure 5: The TEEM desk lamp adjusted to illuminate a book for reading.
Maintenance
Cleaning
- Always unplug the lamp before cleaning.
- Wipe the lamp with a soft, dry cloth. Do not use abrasive cleaners or solvents, as they may damage the finish.
Bulb Replacement
- Ensure the lamp is unplugged and the bulb has cooled completely before attempting to replace it.
- Carefully unscrew the old bulb from the E26 socket.
- Screw in a new E26 base bulb, ensuring it does not exceed 60W.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not turn on. | No power, faulty bulb, or faulty switch. | Check if the power cord is securely plugged in. Test the outlet with another device. Replace the bulb. If issues persist, contact support. |
| Lamp is unstable or wobbles. | Clamp not tightened sufficiently or placed on an uneven surface. | Ensure the clamp is fully tightened. If using the round base, place the lamp on a flat, stable surface. |
| Arm does not hold position. | Springs or joints may need adjustment or tightening. | Check the tension of the springs and the tightness of the joint screws. Adjust as necessary. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | TEEM3535 |
| Material | Metal |
| Finish Type | Painted |
| Shade Material | Fabric |
| Power Source | Corded Electric |
| Bulb Base | E26 |
| Maximum Wattage | 60 Watts (LED or Incandescent) |
| Arm Length | Up to 26 inches (65 cm) total extension (8.7 in + 8.7 in / 22 cm + 22 cm articulated arms) |
| Shade Rotation | 360 degrees |
| Power Cord Length | 4.9 ft (1.5 m) |
| Item Weight | 3.3 pounds (1.5 Kilograms) |
| Product Dimensions | 5.91 x 5.91 x 25.59 inches (approximate, fully extended) |
Figure 6: Detailed dimensions of the TEEM Adjustable Clamp Desk Lamp.
Warranty and Support
For warranty information and customer support, please refer to the documentation provided with your purchase or contact the manufacturer directly. Keep your purchase receipt as proof of purchase.