Introduction
Thank you for purchasing the Outsunny Metal Garden Dining Table. This manual provides essential information for the safe assembly, operation, and maintenance of your new outdoor table. Please read these instructions carefully before use and retain them for future reference.
Image: The Outsunny Metal Garden Dining Table, showcasing its tempered glass top and metal frame, designed for outdoor use.
Safety Information
- Maximum Load Capacity: Do not exceed the maximum load of 154 lbs (70 kg) on the tabletop.
- Stability: Ensure the table is placed on a flat, stable surface to prevent tipping.
- Assembly: Follow all assembly instructions carefully. It is recommended that 4 people assist with assembly for safety and ease.
- Umbrella Use: When using an umbrella with the table, ensure the umbrella is securely anchored and closed during strong winds to prevent damage or injury.
- Glass Top: The tempered glass top is durable but can break if subjected to severe impact. Handle with care.
- Children: Keep children away from the table during assembly and supervise them when near the table during use.
Package Contents
Before beginning assembly, verify that all parts listed below are present and undamaged. If any parts are missing or damaged, do not proceed with assembly and contact customer support.
- Tempered Glass Tabletop
- Metal Frame Components (Legs, Support Bars)
- Hardware Pack (Screws, Washers, Nuts)
- Umbrella Hole Ring and Cap
- Instruction Manual
Tools Required (Not Included): Screwdriver
Setup and Assembly Instructions
Please read all steps before beginning assembly. It is recommended to assemble the table on a soft, clean surface to prevent scratches.
- Unpack Components: Carefully remove all parts from the packaging and lay them out on a protected surface.
- Attach Legs to Frame: Connect the metal legs to the main frame using the provided screws and hardware. Ensure all connections are finger-tight at this stage.
- Install Support Bars: Secure any cross-support bars between the legs or frame as indicated in the diagrams.
- Place Glass Top: Carefully place the tempered glass tabletop onto the assembled frame. Ensure it aligns correctly with the frame and any suction cups or securing points.
- Secure Glass Top: If applicable, secure the glass top to the frame using any provided clips or screws.
- Insert Umbrella Hole Components: Place the umbrella hole ring and cap into the designated opening in the glass top.
- Tighten All Fasteners: Once all components are in place and aligned, fully tighten all screws and fasteners with a screwdriver. Do not overtighten.
- Final Check: Gently shake the table to ensure it is stable and all connections are secure.
Image: A diagram illustrating the dimensions of the dining table, including length, width, height, and umbrella hole diameter.
Image: Detailed view of the table's construction, highlighting round corners, customized sturdy screws, extra support for stability, and unique leg design.
Operating Instructions
This dining table is designed for outdoor use in various settings such as patios, gardens, and balconies.
- Placement: Position the table on a level, stable surface.
- Umbrella Usage: Insert a patio umbrella pole through the center hole. The hole accommodates poles with diameters of 1.45 inches (3.7 cm) or 1.7 inches (4.4 cm). Use the provided cap when an umbrella is not in use.
- Weight Distribution: Distribute weight evenly across the tabletop. Do not place heavy objects on one side only.
Image: The Outsunny dining table set up on a patio with an umbrella and two chairs, demonstrating its intended use.
Image: A graphic illustrating the versatility of the table for use in various outdoor environments like patios, poolside, and gardens, as well as indoor spaces.
Maintenance
- Cleaning: Wipe the tempered glass top and metal frame with a damp cloth. For stubborn dirt, use a mild soap solution and rinse thoroughly. Avoid abrasive cleaners or harsh chemicals.
- Inspection: Periodically check all screws and fasteners to ensure they remain tight. Retighten as necessary.
- Weather Protection: While designed for outdoor use, covering the table during extreme weather conditions (heavy rain, snow, strong winds) or prolonged periods of non-use will extend its lifespan.
- Storage: If storing indoors for the off-season, ensure the table is clean and dry.
Image: Close-up views detailing the 5mm thick water wave tempered glass, the durable metal construction frame, and the built-in umbrella hole with its components.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Table is wobbly after assembly. | Fasteners are not fully tightened or table is on an uneven surface. | Ensure all screws and bolts are securely tightened. Move the table to a level surface. |
| Glass top does not sit flush. | Frame components are not assembled correctly or glass is misaligned. | Disassemble and re-assemble the frame, ensuring all parts are correctly oriented. Carefully re-position the glass top. |
| Umbrella does not fit in the hole. | Umbrella pole diameter is too large or too small for the provided inserts. | Verify your umbrella pole diameter. The table accommodates 1.45" (3.7 cm) or 1.7" (4.4 cm) poles. |
Specifications
- Model: 84B-376V01
- Overall Dimensions: 47.25" L x 31.5" W x 27.5" H (120 cm L x 80 cm W x 70 cm H)
- Material: Metal frame, Tempered Glass top
- Color: Carbon Grey
- Item Weight: 13.97 kg (30.8 lbs)
- Maximum Load Capacity: 154 lbs (70 kg)
- Umbrella Hole Diameter: 1.45" (3.7 cm) / 1.7" (4.4 cm) or 44 mm
- Assembly Required: Yes
- Recommended Assembly Persons: 4
- Care Instructions: Wipe Clean
Warranty and Support
This Outsunny product comes with a 90-day warranty against manufacturer defects. Please retain your proof of purchase for warranty claims.
For customer support, missing parts, or warranty inquiries, please contact Aosom Canada:
- Manufacturer: Aosom Canada
- Location: Markham, Ontario, CA
- Telephone: 1-416-792-6088