MC Modular Closets Double Hanging Closet Unit (White, 19.5 Inches Wide) - Instruction Manual

1. Product Overview

This manual provides detailed instructions for the assembly, installation, and maintenance of your MC Modular Closets Double Hanging Closet Unit. This unit is designed to integrate seamlessly with other Modular Closets components, offering a customizable storage solution for your wardrobe.

The Double Hanging Unit features two levels of hanging rods, ideal for organizing shorter garments such as shirts, pants, and skirts. It is 19.5 inches wide and can support up to 200 lbs. The modular system is wall-mounted, ensuring a strong and stable installation.

Image 1.1: The Double Hanging Closet Unit, showcasing its two hanging rods and storage capacity.

Key Features:

• Double Hanging Capacity: Two levels of hanging rods for efficient organization of shorter garments.
• Robust Construction: Made from 3/4" M-2 grade furniture board with a high-quality Thermally Fused Laminate (TFL) finish.
• Wall-Mounted Design: Patented system for secure wall installation, maximizing floor space.
• Modular System: Designed to integrate with other Modular Closets components for a custom closet layout.
• High Load Capacity: Can hold up to 200 lbs.

2. Before You Begin: Planning & Tools

Careful planning ensures a smooth installation process. Before starting, measure your closet space and gather the necessary tools.

2.1 Measuring Your Space:

Measure the width, height, and depth of your closet walls. Note any obstructions like baseboards or crown molding. This unit is 19.5 inches wide, 14 inches deep, and 46 inches high. Ensure adequate space for installation and use.

Image 2.1: Dimensional diagram of the Double Hanging Closet Unit, showing its width, depth, and height.

Consider the placement of other modular components if you are building a larger system. The unit is designed to be wall-mounted at 84 inches high when installed, but can be adjusted to any desired height as long as there is enough space.

2.2 Required Tools:

• Phillips Head Screwdriver (or power drill with Phillips bit)
• Rubber Mallet
• Tape Measure
• Pencil
• Stud Finder
• Level
• Optional: Third-arm support device or a helper for hanging units.

3. Assembly Instructions

Follow these steps carefully to assemble your Double Hanging Closet Unit. Refer to the included item list to ensure all components are present and undamaged before beginning.

3.1 Unboxing and Inventory:

1. Carefully open the packaging using a razor around the outside edges to avoid scratching internal materials.
2. Lay out all contents and verify against the provided item list to ensure nothing is missing or damaged.

3.2 Unit Assembly:

3. Screw the cam posts into the designated holes on the side panels. Use a screwdriver or drill, being careful not to overtighten.
4. Place the fixed shelves and cleats onto the cam posts. Ensure the shelves with cam lock holes face away from view.
5. Attach the second side panel onto the fixed shelves and cleats. Align the cam posts into the holes and ensure all components are properly aligned. Use a rubber mallet to gently tap the dowels into place if needed.
6. Insert a cam lock into each hole in the cleats and fixed shelves. Ensure the arrow on the cam lock points towards the head of the screw.
7. Tighten the cam locks by turning the screwdriver clockwise. Avoid overtightening to prevent damage.

4. Installation Instructions

Proper installation is crucial for the stability and longevity of your closet unit. This unit is designed for wall mounting.

4.1 Wall Preparation:

1. Use a stud finder to locate wall studs where the unit will be mounted. Mark the stud locations with a pencil. Studs are typically 16 inches apart.
2. Determine the desired height for your unit. While 84 inches off the ground is recommended, units can be adjusted to any desired height with sufficient space.
3. Pre-drill pilot holes on the unit's cleats at each marked stud location.

4.2 Mounting the Unit:

4. With the help of a second person or a third-arm support device, lift the assembled unit into position against the wall.
5. Ensure the unit is level using a spirit level to avoid installation complications.
6. Drill the unit directly into the wall studs through the pre-drilled pilot holes in the cleats. Use appropriate screws for secure attachment.
7. For added support when installing multiple units side-by-side, you can drill a 1.25-inch screw from one unit to the other. These screws can be concealed behind hanging brackets or at the rear of the unit.

4.3 Installing Hanging Rods:

8. Once the unit is securely mounted, install the hanging bars.
9. Drill the U-shaped bracket to one side panel.
10. Slide the O-bracket onto the rod.
11. Drill the screws into the other side panel to secure the rod.

5. Operating Your Closet Unit

Your Double Hanging Closet Unit is designed for efficient and organized storage of your garments.

5.1 Utilizing Hanging Space:

• Use the two hanging rods to separate different types of shorter clothing, such as shirts on the top rod and pants or skirts on the bottom rod.
• Ensure garments are evenly distributed to maintain balance and prevent excessive strain on the rods.

Image 5.1: Example of an organized closet utilizing double hanging rods for various garments.

6. Maintenance

To keep your Modular Closets unit in optimal condition, follow these simple maintenance guidelines:

• Cleaning: Wipe surfaces with a soft, damp cloth. Avoid abrasive cleaners or harsh chemicals that could damage the Thermally Fused Laminate (TFL) finish.
• Inspection: Periodically check all screws and connections to ensure they remain tight. Retighten if necessary.
• Load Management: Do not exceed the maximum weight capacity of 200 lbs for the unit. Distribute weight evenly across the hanging rods.

7. Troubleshooting

If you encounter any issues during assembly or use, refer to the following common troubleshooting tips:

• Missing or Damaged Parts: Before assembly, carefully check all components against the item list. If any parts are missing or damaged, contact MC Modular Closets customer support immediately.
• Unit Not Level: During installation, use a spirit level to ensure the unit is perfectly horizontal. Adjust mounting screws as needed to achieve a level position.
• Difficulty with Cam Locks: Ensure cam posts are fully screwed in and cam locks are inserted with the arrow pointing towards the screw head before tightening. Do not overtighten.
• Unit Instability: Verify that the unit is securely mounted into wall studs. If only drywall anchors were used, consider relocating to stud locations for maximum stability.

8. Specifications

9. Warranty & Support

MC Modular Closets stands behind the quality of its products.

• Forever Warranty: This product is covered by our Forever Warranty. For details, please refer to the warranty information provided with your purchase or visit the official MC Modular Closets website.
• Customer Support: Our dedicated team is available to assist you with any questions regarding installation, product use, or troubleshooting. Contact information can be found on the official MC Modular Closets website or through your purchase platform.