1. Important Safety Information
Read and understand all instructions and warnings before using the Tesoro Moda Full Face Organic Vapor Respirator. Failure to follow these instructions may result in serious injury or death. This respirator is designed to protect against certain airborne contaminants. It is crucial to select the correct filters for the specific hazards present in your work environment.
- Do not use this respirator in atmospheres containing less than 19.5% oxygen.
- Do not use this respirator in atmospheres that are immediately dangerous to life or health (IDLH).
- Do not use this respirator if you have a beard or other facial hair that prevents a good face-to-respirator seal.
- Consult a safety professional to determine the appropriate respiratory protection for your specific application.
- This mask is not compatible with glasses.
2. Product Overview and Components
The Tesoro Moda Full Face Organic Vapor Respirator provides comprehensive protection for your eyes, face, and respiratory system. It features a durable lens, an airtight silicone seal, and a dual-filter system for effective filtration.
Image: The Tesoro Moda Full Face Organic Vapor Respirator with its two filter cartridges attached.
Components:
- Full Face Mask Body: Main structure with lens and head harness.
- Head Harness: Adjustable straps for a secure fit.
- Exhalation Valve: Reduces heat and humidity inside the mask.
- Inhalation Valves: Control airflow into the mask.
- Filter Cartridges (P-A-1): Two activated charcoal filters for organic vapors and particulates.
- Cotton Filters: Pre-filters for particulates, placed inside the cartridge covers.
- Cartridge Covers: Secure the cotton filters and direct airflow.
- Voice Amplification Diaphragm: Enhances communication.
Image: An exploded view illustrating the filter cartridge, cotton filter, and cover components of the respirator.
3. Setup and Assembly
Before first use, or after cleaning, assemble the filter components as follows:
- Insert Cotton Filter: Place a cotton filter into the designated slot within the cartridge cover base.
- Attach Cartridge Cover: Secure the cartridge cover base onto the activated charcoal filter cartridge.
- Attach Filter Assembly to Mask: Align the assembled filter cartridge with the connection port on the side of the mask. Turn the cartridge 90 degrees clockwise until it clicks securely into place.
- Verify Security: Ensure both filter assemblies are properly closed and firmly attached to the mask body.
Image: A visual guide demonstrating the four steps for filter assembly: placing the cotton filter, fitting the cover, aligning with the mask, and securing it.
Adjusting the Head Harness:
The respirator features an adjustable 5-point head harness. Loosen all straps before putting on the mask. Once the mask is on your face, tighten the straps evenly, starting from the bottom straps, then the middle, and finally the top, until a comfortable yet secure seal is achieved. Do not overtighten.
4. Operating Instructions
Wearing the Respirator:
- Ensure filters are correctly installed.
- Hold the mask with one hand and pull the head harness over your head with the other.
- Position the mask firmly on your face, ensuring your chin is properly seated in the chin cup.
- Pull the head harness straps to adjust for a snug, comfortable fit. Ensure no hair is caught under the seal.
- Perform a seal check.
Image: A person wearing the full face respirator, demonstrating its use for protection against various airborne hazards.
Performing a Seal Check:
A proper seal is critical for effective protection. Perform a positive and negative pressure seal check every time you don the the respirator.
- Positive Pressure Seal Check: Place the palm of your hand over the exhalation valve cover and gently exhale. The mask should bulge slightly, and no air should leak from the edges of the mask.
- Negative Pressure Seal Check: Place the palms of your hands over the filter cartridges (or inhalation valve covers if applicable) and gently inhale. The mask should pull inward towards your face, and no air should leak from the edges of the mask.
If you detect any leakage during either check, readjust the mask and straps, then repeat the seal check. If a proper seal cannot be achieved, do not enter the contaminated area.
Intended Use:
This respirator is suitable for environments where protection against organic vapors, certain chemicals, dust, and particulates is required. This includes applications in agriculture, construction, mining, welding, painting, and woodworking. The built-in voice amplification diaphragm aids in clearer communication without removing the mask.
5. Maintenance and Storage
Cleaning the Mask:
After each use, clean the mask body (excluding filters) with mild soap and warm water. Rinse thoroughly with clean water and allow to air dry completely in a clean, non-contaminated area away from direct sunlight. Do not use harsh solvents or abrasive cleaners.
Filter Replacement:
Filter cartridges and cotton filters must be replaced regularly. The frequency of replacement depends on the concentration of contaminants, breathing rate, humidity, and other environmental factors. Replace filters immediately if you detect any odor or taste of contaminants, or if breathing becomes difficult.
- The date printed on the filter package is the manufactured date. Filters have a shelf life of 3 years from this date.
- Replacement filters (ASIN: B08P2TQ387) are readily available.
Image: A set of replacement filter cartridges and cotton filters for the respirator.
Storage:
Store the respirator in a clean, dry, and cool place away from direct sunlight, chemicals, and extreme temperatures. Keep it in a sealed bag or container to prevent contamination and prolong filter life.
6. Troubleshooting
- Difficulty Breathing:
- Check if filters are clogged or past their service life. Replace if necessary.
- Ensure inhalation and exhalation valves are clean and not obstructed.
- Detection of Odor/Taste:
- Indicates filter breakthrough. Immediately leave the contaminated area and replace both filter cartridges.
- Perform a seal check to ensure proper fit.
- Air Leakage Around Face Seal:
- Readjust head harness straps for a tighter, more even fit.
- Ensure no hair or clothing is interfering with the seal.
- Verify the mask size is appropriate for your face.
- Fogging of Lens:
- The mask features an anti-fog lens. Ensure the mask is properly sealed to allow the airflow valve to function effectively.
- Clean the lens with a soft cloth and anti-fog solution if persistent.
7. Specifications
Image: Detailed technical specifications for the respirator.
| Feature | Detail |
|---|---|
| Protection Level | Class 2 |
| Head Strap | Adjustable 5-point harness |
| Thread Connection | Standard 40mm NATO Thread (RD40) |
| Weight | 1.4 to 1.6 lbs |
| Shelf Life (Filters) | 3 Years from manufactured date |
| Storage Condition | Temperatures 10°C to 50°C (14°F to 122°F), Humidity below 70%. |
| Inhalation Resistance | Initial Resistance: ≤ 2.0 mbar (200 Pa) With Filters: ≤ 5.0 mbar (500 Pa) |
| Exhalation Resistance | Typically ≤ 3.0 mbar (300 Pa) |
| Inward Leakage | Total Inward Leakage: < 0.05% With Filters: ≤ 5.0 mbar (500 Pa) |
| Carbon Dioxide Content of Inhalation Air | Below 1% by volume |
| Effective Field of Vision | 80-85% |
| Overlapped Field of Vision | 70% to 80% |
8. Warranty and Support
Tesoro Moda is committed to providing quality products and customer satisfaction. For any questions regarding the use, maintenance, or performance of your respirator, please contact our customer support.
As a trusted American seller, Tesoro Moda offers responsive customer care and support. Please refer to your purchase documentation for specific warranty details.
Contact Information: Please visit the Tesoro Moda Store on Amazon for further assistance or to find replacement parts.
