Jandy R0693900 TruClear Salt Cell Assembly Instruction Manual

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Jandy R0693900 TruClear Salt Cell Assembly. Please read this manual thoroughly before attempting any procedures to ensure safe and efficient use of the product.

2. Important Safety Information

Always disconnect power to the pool equipment at the main breaker before performing any service or maintenance.
Wear appropriate personal protective equipment, including safety glasses and gloves, when handling pool chemicals or performing maintenance.
Do not use undiluted muriatic acid for cleaning the salt cell, as this can cause severe damage to the cell and void the warranty. Always follow manufacturer guidelines for chemical dilution and handling.
Ensure all plumbing connections are secure and watertight to prevent leaks.

3. Product Overview

The Jandy R0693900 TruClear Salt Cell Assembly is a replacement component for Jandy Pro Series TruClear Chlorinators, designed to generate chlorine for your pool from salt. This assembly includes the cell and its integrated power cable.

Figure 1: Jandy R0693900 TruClear Salt Cell Assembly, showing the cell body and coiled power cable.

4. Installation Instructions

Replacing the Jandy TruClear Salt Cell Assembly is a straightforward process. Follow these steps carefully:

Video 1: Overview of the Jandy Salt Cell replacement process, demonstrating ease of installation.

4.1. Step 1: Disconnect Power

Before beginning any work, ensure the pool pump and all associated electrical components are turned off at the main circuit breaker. This prevents accidental startup and electrical hazards.

4.2. Step 2: Drain Water

Open the air relief valve at the top of your pool filter to allow water to drain from the system. This will lower the water level in the plumbing, preventing water from spilling when the salt cell is removed.

4.3. Step 3: Remove Old Salt Cell

Locate the existing salt cell in your pool's plumbing system. The cell is typically installed in-line with the return plumbing to the pool. Unscrew the locking ring that secures the cell to the plumbing. Carefully lift the old salt cell assembly out of its housing. Disconnect the power cable from the control box.

Figure 2: The existing Jandy salt cell integrated into the pool's plumbing system.

Close-up of Jandy Salt Cell electrical connector

Figure 3: Close-up view of the electrical connector for the Jandy salt cell, which needs to be disconnected from the control box.

4.4. Step 4: Install New Salt Cell

Insert the new Jandy R0693900 TruClear Salt Cell Assembly into the plumbing housing. Ensure the flow arrows on the cell align with the direction of water flow in your plumbing. Tighten the locking ring securely to prevent leaks. Connect the power cable of the new cell to the Jandy TruClear control box.

Figure 4: The new Jandy R0693900 salt cell assembly, ready for installation, showing the integrated cable.

Top view of Jandy Salt Cell showing flow indicators

Figure 5: Top view of the salt cell, highlighting the flow indicators for correct orientation during installation.

4.5. Step 5: Restore Power and Check Operation

Close the air relief valve on the filter. Restore power to the pool pump and control box at the main circuit breaker. Turn on the pool pump. Verify that the Jandy TruClear control box indicates

Related Documents - R0693900

	Jandy TruClear Cell Replacement: Spare Parts Installation Guide Official installation instructions for the Jandy TruClear Cell Replacement (Part R0693900) for Jandy Pro Series pool systems. Includes safety warnings, package contents, and step-by-step installation procedures.
	Jandy AquaPure Ei Series APURE35PLG Chlorine Generating Device Installation and Operation Manual Comprehensive installation and operation manual for the Jandy AquaPure Ei Series APURE35PLG 120V Plug-In Chlorine Generating Device. Covers safety, system description, installation, water preparation, operation, maintenance, and troubleshooting.
	Jandy VS Pumps & Gas Heaters: Drop-In Replacement Guide A comprehensive guide from Jandy for pool professionals and homeowners on replacing existing pool pumps and gas heaters with Jandy VS FloPro pumps and JXi heaters. Features include easy installation, performance benefits, technical specifications, and comparison charts with Pentair and Hayward models.
	Jandy AquaLink RS All Button and OneTouch Control Systems Installation Manual Comprehensive installation guide for Jandy AquaLink RS control systems, covering All Button and OneTouch models. This manual provides detailed instructions for setup, wiring, programming, and troubleshooting pool and spa automation equipment.
	Jandy Pro Series Pool and Spa Air Blower Installation Guide Detailed installation guide for Jandy Pro Series Pool and Spa Air Blowers (Models PSB110, PSB115, PSB120, PSB210, PSB215, PSB220). Covers essential safety precautions, blower sizing calculations, plumbing configurations (Standard, Long Run, Below Grade, Hartford Loop), and electrical wiring instructions for safe and effective operation.
	Jandy Commercial Salt Chlorinator: Installation and Operation Manual Comprehensive guide for installing, operating, and maintaining Jandy Commercial Salt Chlorinators (Models JSWC40, JSWC53, JSWC80, JSWC100). Covers safety, system description, installation, operation, maintenance, and troubleshooting.