1. Introduction
Thank you for choosing the ezonpinzv UL Listed Through-Cord Slide Full-Dimmer Switch. This manual provides important information regarding the installation, operation, and maintenance of your new dimmer switch. Please read this manual thoroughly before installation and use, and retain it for future reference.
This dimmer switch is designed for use with dimmable LED, CFL, and incandescent lamps, operating at 120VAC 60Hz. It features a full-range dimming function to adjust light intensity.
2. Safety Information
WARNING: To avoid fire, shock, or death; turn off power at circuit breaker or fuse and test that power is off before wiring! This device is for indoor and dry location use only. Do not use outdoors or in wet environments.
- Always disconnect power before installing or servicing the switch.
- Do not exceed the specified electrical ratings: Dimmable LED/CFL: 100W 120VAC 60Hz; Incandescent: 300W 120VAC 60Hz.
- Not suitable for non-dimmable LED and CFL bulbs. Using with non-dimmable bulbs may cause damage to the bulb or the dimmer.
- Ensure all wire connections are secure and properly insulated.
- Consult a qualified electrician if you are unsure about any part of the installation process.
3. Product Overview
The ezonpinzv Through-Cord Slide Full-Dimmer Switch is designed for easy integration into existing lamp cords. It features a simple slide control for dimming and an on/off function.
Figure 3.1: Front view of the ezonpinzv Through-Cord Slide Full-Dimmer Switch. The image shows the white plastic casing with a central slide control and a small red indicator light.
Figure 3.2: Internal view of the dimmer switch with the casing open. It reveals the circuit board, slide mechanism, and wiring terminals (Lout, Lin).
Key Components:
- Slide Control: Adjusts light brightness and acts as an on/off switch.
- Indicator Light: A small red LED that typically indicates power or operation.
- Wiring Terminals: Internal connections for input (Lin) and output (Lout) wires.
4. Specifications
| Feature | Description |
|---|---|
| Operation Mode | Slide |
| Current Rating | 3.7 Amps |
| Operating Voltage | 120 Volts AC |
| Contact Type | Normally Closed |
| Connector Type | Screws |
| Terminal | Solder |
| Item dimensions L x W x H | 3.3 x 1.57 x 0.98 inches |
| Circuit Type | 1-way |
| Actuator Type | Slide |
| Dimmable LED Lamp Rating | 100W 120VAC 60Hz |
| Dimmable CFL Rating | 100W 120VAC 60Hz |
| Incandescent Lamp Rating | 300W 120VAC 60Hz |
| Input | 120VAC 60Hz |
| Indoor Use Only | Yes |
| Compatibility | Dimmable LED, CFL, Incandescent bulbs (Not for non-dimmable types) |
5. Setup and Installation
This dimmer switch is designed for through-cord installation. Follow these steps carefully:
- Disconnect Power: Ensure the lamp or appliance cord is unplugged from the wall outlet before beginning installation.
- Prepare the Cord: Determine the desired location for the dimmer switch on the lamp cord. Carefully cut the cord at this point. Separate the two wires of the cord for about 1-2 inches on both cut ends.
- Strip Wires: Strip approximately 1/2 inch of insulation from the ends of all four wires (two from each cut end of the cord).
- Open the Dimmer Casing: Gently open the dimmer switch casing. It typically snaps open or has small screws. Refer to Figure 5.1 for internal view.
Figure 5.1: Top view of the open dimmer switch, showing the "IN" and "OUT" sides, and the internal terminals for wiring.
- Connect Wires:
- Identify the "IN" side of the dimmer (where power comes from the wall outlet) and the "OUT" side (where power goes to the lamp).
- Connect one wire from the "IN" side of the cut cord to the "Lin" terminal inside the dimmer.
- Connect the other wire from the "IN" side of the cut cord to the "Lout" terminal inside the dimmer.
- Connect one wire from the "OUT" side of the cut cord to the remaining "Lin" terminal.
- Connect the other wire from the "OUT" side of the cut cord to the remaining "Lout" terminal.
Note: Ensure that the correct wires are connected to the corresponding terminals (e.g., ribbed wire to one side, smooth wire to the other, consistently). Some cords have one ribbed wire and one smooth wire for polarity. Maintain this polarity if applicable.
Figure 5.2: Close-up view of the internal wiring terminals (Lin and Lout) within the dimmer switch, showing where the stripped wires should be connected.
- Secure Wires: Tighten the screw terminals to secure the wires. Gently tug on each wire to ensure it is firmly connected and will not pull out.
- Close Casing: Carefully close the dimmer switch casing, ensuring no wires are pinched and the casing snaps securely shut.
- Test: Plug the lamp or appliance cord back into the wall outlet and test the dimmer switch.
6. Operating Instructions
Operating the ezonpinzv Through-Cord Slide Full-Dimmer Switch is straightforward:
- Turning On/Off: Slide the control lever fully to the "ON" or "OFF" position.
- Dimming: Once the light is on, slide the control lever up or down to adjust the brightness level. Sliding it up typically increases brightness, and sliding it down decreases brightness.
- Indicator Light: The red indicator light will illuminate when the switch is in operation.
7. Maintenance
The ezonpinzv Through-Cord Slide Full-Dimmer Switch requires minimal maintenance:
- Cleaning: Disconnect power before cleaning. Wipe the exterior of the switch with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Inspection: Periodically inspect the cord and the switch for any signs of damage, fraying, or loose connections. If any damage is found, discontinue use and replace the switch.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power to the outlet; Bulb is burnt out; Loose wiring connection; Non-dimmable bulb. | Check circuit breaker/fuse; Replace bulb; Re-check wiring connections (ensure power is off first); Ensure bulb is dimmable. |
| Light flickers or hums. | Incompatible bulb (non-dimmable or poor quality dimmable); Overloaded circuit; Loose connection. | Replace with a high-quality dimmable LED/CFL or incandescent bulb; Ensure total wattage does not exceed dimmer rating; Check wiring connections. |
| Dimmer does not dim properly. | Non-dimmable bulb; Bulb not compatible with full-range dimming; Dimmer damaged. | Ensure bulb is specifically designed for dimming; Try a different dimmable bulb; If problem persists, the dimmer may need replacement. |
| Red indicator light is off. | No power to the switch; Switch is in "OFF" position; Faulty indicator light. | Check power supply; Slide switch to "ON" position; If switch functions but light is off, it may be a minor cosmetic issue. |
9. Warranty and Support
This ezonpinzv product is manufactured with high-quality materials and craftsmanship. While specific warranty details are not provided in this manual, most products come with a standard manufacturer's warranty against defects in materials and workmanship.
For technical support, warranty claims, or further assistance, please contact your retailer or the manufacturer directly through their official website or customer service channels. Please have your product model information and purchase date available when contacting support.