dalattin 65.6ft RGB LED Strip Lights

1. Introduction

The dalattin 65.6ft RGB LED Strip Lights (Model: TB50121044R-RA01) provide versatile and vibrant lighting for various indoor applications. This product includes two 32.8ft rolls of LED strip lights, a 44-key IR remote control, an IR receiver, and a power adapter. Designed for ease of use and installation, these lights are suitable for enhancing the ambiance of bedrooms, living rooms, ceilings, and for special occasions like parties and festivals.

The LED strips are cuttable along designated markings, allowing for customization to fit specific spaces. They feature a self-adhesive backing for simple installation on dry, flat surfaces. Control is managed via the included IR remote, offering a wide range of colors, adjustable brightness, and various lighting modes.

Image 1.1: Examples of dalattin LED strip lights installed in various indoor settings, including a living room, corridor, studio, and lockers, demonstrating their versatility for ambient lighting.

2. Package Contents

Please verify that all items listed below are included in your package:

• 2 x 32.8ft RGB LED Strip Lights (Total 65.6ft)
• 1 x 44-Key IR Remote Control
• 1 x IR Receiver Box
• 1 x Power Adapter

Image 2.1: The complete package contents, including the LED strip rolls, 44-key remote, and power supply components.

3. Setup and Installation

Follow these steps for proper installation of your dalattin LED Strip Lights:

1. Surface Preparation: Ensure the surface where you intend to install the lights is clean, dry, and smooth. Dust, dirt, or moisture can affect the adhesive's effectiveness.
2. Connect Components:
   • Connect the power adapter to the IR receiver box.
   • Connect the LED strip lights to the IR receiver box. Ensure the arrows on the strip connector and the IR receiver are aligned. Important: If the lights do not turn on, try reversing the connection of the 4-pin connector to the IR receiver, as there is a specific positive/negative orientation.
3. Remove Remote Battery Tab: Before first use, pull out the transparent plastic tab from the battery compartment of the 44-key IR remote control.
4. Adhere LED Strips: Carefully peel off the protective backing from the 3M self-adhesive tape on the back of the LED strip. Press the strip firmly onto the prepared surface. Avoid repositioning the strip multiple times, as this can weaken the adhesive.
5. Power On: Plug the power adapter into a standard electrical outlet. The lights should now be ready for operation using the remote control.

Image 3.1: Connection diagram illustrating the proper way to connect the power adapter, IR receiver, and LED strip lights. Note the arrow alignment for correct polarity.

Image 3.2: Detail of the 3M super strong self-adhesive backing on the LED strip, indicating the rubber-coated surface and how to peel off the protective layer for installation.

4. Operating Instructions

The dalattin LED Strip Lights are controlled using the included 44-key IR remote control. Ensure the remote is pointed directly at the IR receiver box for optimal response.

4.1 Remote Control Functions

• Power Button (On/Off): Turns the LED lights on or off.
• Brightness Adjustment: Use the UP and DOWN arrow buttons to increase or decrease the brightness.
• Color Selection: Press the colored buttons (Red, Green, Blue, White, and various mixed colors) to select a static color.
• DIY Modes: The DIY1, DIY2, DIY3, DIY4, DIY5, DIY6 buttons allow you to save custom color mixes. To set a custom color: press a DIY button, then use the RGB arrow buttons to adjust the color, and press the same DIY button again to save.
• Pre-programmed Modes:
  • FLASH: Rapid color changes.
  • STROBE: White light flashes.
  • FADE: Smooth transition through colors.
  • SMOOTH: Gradual transition through RGB colors.
  • QUICK/SLOW: Adjusts the speed of dynamic modes.

Image 4.1: The 44-key IR remote control, demonstrating its layout and the wide array of static color options available for the LED strip lights.

5. Maintenance and Care

Proper maintenance ensures the longevity and optimal performance of your LED strip lights:

• Cleaning: Gently wipe the LED strips with a dry, soft cloth to remove dust. Do not use liquid cleaners or abrasive materials, as they can damage the LEDs or the protective coating.
• Handling: Avoid sharp bends or excessive pulling on the LED strips, especially near the connection points, as this can damage the internal circuitry.
• Storage: If storing the lights for an extended period, ensure they are clean and dry. Store them in a cool, dry place away from direct sunlight and extreme temperatures.
• Adhesive Care: The self-adhesive tape is designed for a single, firm application. Repeated removal and reapplication may reduce its stickiness.

6. Troubleshooting

If you encounter issues with your dalattin LED Strip Lights, refer to the following common problems and solutions:

7. Product Specifications

8. Warranty and Support

dalattin is committed to providing high-quality products and customer satisfaction. For any product-related inquiries, technical support, or warranty claims, please contact dalattin customer service through the retailer's platform or the official dalattin website. Please retain your proof of purchase for warranty purposes.