RXWLKJ Rechargeable Motion Sensor LED Lights

Introduction

Thank you for choosing the RXWLKJ Rechargeable Motion Sensor LED Lights. This manual provides essential information for the safe and efficient use of your new lighting solution. Please read these instructions carefully before installation and operation, and retain them for future reference.

Package Contents

Verify that all items listed below are included in your package:

• 2 x Rechargeable Motion Sensor LED Lights (12.7 inches, 54 LEDs)
• 2 x Metal Mounting Strips
• 4 x Double-sided Adhesive Pads
• 2 x USB Charging Cables (Micro B)
• 1 x User Manual

Key Features

• Super Bright & Eye-Protection: Equipped with 54 LED beads, providing up to 350 lumens. Features a light guide panel for glare-free, flicker-free illumination.
• Easy Installation: Built-in magnets allow direct attachment to iron surfaces. For non-magnetic surfaces like wood or aluminum, use the included metal strips and adhesive pads. No wiring required.
• USB Rechargeable: Features a built-in 2500mAh battery. Rechargeable via a standard USB (Micro B) cable, eliminating the need for disposable batteries.
• 3 Operating Modes: A 3-mode switch (On/Off/G) allows selection between always ON, OFF, or Motion Sensor mode.
• Motion Sensor Functionality: In 'G' mode, the light automatically senses human motion within a 10ft/120° range in dark environments and turns off after 20 seconds of no movement.
• Versatile Use: Ideal for laundry rooms, bedrooms, baby rooms, drawers, garages, closets, cabinets, attics, and other dark areas.

Setup & Installation

The RXWLKJ LED lights offer flexible installation options due to their magnetic design.

1. Prepare the Surface: Ensure the desired installation surface is clean and dry.
2. Apply Adhesive Pads: Peel the protective film from one side of the double-sided adhesive pads. Attach these pads to the metal mounting strip.
3. Mount the Metal Strip: Peel the remaining protective film from the adhesive pads and firmly press the metal strip onto the chosen surface.
4. Attach the Light: The LED light bar has built-in magnets. Simply align the light bar with the mounted metal strip, and it will securely attach magnetically. This allows for easy removal for charging or repositioning.

Charging Instructions

Your LED lights are equipped with a rechargeable battery for convenience.

1. Connect the Cable: Insert the Micro B end of the USB charging cable into the charging port on the light bar.
2. Connect to Power: Plug the USB-A end of the cable into a standard USB charger (e.g., phone charger, computer USB port).
3. Monitor Charging: A red indicator light will illuminate during charging. Once fully charged, the indicator light will turn green.
4. Charging Time: A full charge typically takes approximately 3 hours.

Operating Modes

The light features a 3-way switch to select your preferred operating mode:

• ON: The light will remain continuously on.
• OFF: The light will remain off.
• G (Motion Sensor Mode): In this mode, the light will automatically turn on when motion is detected within its 10ft/120° range. It will only activate in dim light or dark environments. The light will automatically turn off after approximately 20 seconds of no movement.

Applications

These versatile LED lights are suitable for a wide range of indoor applications:

• Under kitchen cabinets
• Closets and wardrobes
• Pantries and storage areas
• Staircases and hallways
• Drawers and shelves
• Children's rooms and nurseries
• Garages and workshops
• Car trunks

Specifications

Maintenance

• Cleaning: Wipe the light surface with a soft, dry cloth. Do not use abrasive cleaners or solvents.
• Charging: Recharge the battery when the light output appears dim or the indicator light signals low battery. Avoid fully depleting the battery for extended periods.
• Storage: If storing the lights for a long time, charge them fully every 3-6 months to maintain battery health.
• Environment: Do not expose the lights to extreme temperatures or high humidity. These lights are not waterproof and should not be used in wet conditions.

Troubleshooting

• Light not turning on in Motion Sensor (G) mode: Ensure the environment is sufficiently dark. The motion sensor is designed to activate only in low-light conditions to conserve battery. Check if the battery is charged.
• Light not detecting motion: Verify that the sensor is not obstructed. Ensure the light is within the 10ft/120° detection range.
• Short battery life: Ensure the light is fully charged. Frequent activation in high-traffic areas will consume battery faster. Consider using 'OFF' mode when not needed for extended periods.
• Light falling off: Ensure the mounting surface is clean and smooth before applying adhesive. For heavy items or rough surfaces, consider using stronger adhesive or alternative mounting methods if necessary.

Warranty and Support

RXWLKJ is committed to providing high-quality products and excellent customer service. For any inquiries or support, please refer to the following:

• Customer Service: 24/7 support is available.
• Replacement Warranty: Enjoy a 12-month replacement warranty from the date of purchase.
• Money-Back Guarantee: A 60-day money-back guarantee is provided for your peace of mind.

For further assistance, please contact RXWLKJ customer support through your purchase platform.