Hayward VS 900

Hayward TriStar VS 900 Variable-Speed Pump User Manual

Model: VS 900

Introduction

This manual provides essential information for the installation, operation, and maintenance of your Hayward TriStar VS 900 Variable-Speed Pump. Please read this manual thoroughly before attempting to install or operate the pump. Proper installation and maintenance are crucial for optimal performance, energy efficiency, and longevity of the unit.

Image: The Hayward TriStar VS 900 Variable-Speed Pump, a black unit with a clear strainer lid and an electronic control panel on top. The pump features an ENERGY STAR label on its side, indicating its energy efficiency.

Safety Information

Always follow basic safety precautions to reduce the risk of injury, fire, electric shock, or property damage.

Disconnect power before servicing.
Ensure proper grounding and bonding.
Do not operate if the pump is damaged.
Consult a qualified pool professional for installation and major repairs.

Setup and Installation

The TriStar VS 900 pump is designed for easy integration into new and existing pool systems. It features side/rear conduit entries and standard union connections.

Pre-Installation Checklist:

Verify power supply matches pump requirements (dual-voltage motor drive).
Ensure adequate ventilation around the pump.
Confirm plumbing connections are clean and free of debris.

Installation Steps:

Mounting: Secure the pump on a level, solid surface to minimize vibration and noise.
Plumbing: Connect the pump to your pool's plumbing system using standard union connections. Ensure all connections are watertight.
Electrical Wiring: Connect the pump to the appropriate power supply. The side and rear conduit entry points accommodate both high and low voltage connections. This step should be performed by a qualified electrician.
Priming: Before initial startup, fill the pump's strainer basket with water to prime the pump.

Operating Instructions

The TriStar VS 900 features an intuitive control panel for easy operation and programming.

Initial Startup:

Ensure the pump is primed.
Restore power to the pump.
The pump will typically run a self-diagnostic check.

Programming Speeds and Schedules:

Utilize the control panel to set desired operating speeds and schedules. Variable-speed pumps allow for significant energy savings by running at lower speeds for longer durations, which is ideal for filtration.

High-Speed Operation: Use for backwashing, vacuuming, or when rapid water circulation is needed. The upgraded dual-voltage motor drive ensures quiet high-speed operation.
Low-Speed Operation: Ideal for daily filtration, maximizing energy efficiency and minimizing noise.
Refer to the on-screen prompts and dedicated buttons on the control panel for detailed programming instructions.

Maintenance

Regular maintenance ensures the longevity and efficient operation of your TriStar VS 900 pump.

Strainer Basket Cleaning:

The pump features a no-rib strainer basket with a see-through cover for easy debris removal.

Turn off the pump and disconnect power.
Unscrew the clear strainer cover.
Remove the basket and empty any debris.
Rinse the basket and inspect for damage.
Replace the basket and secure the cover, ensuring the O-ring is properly seated for a watertight seal.

Seal Inspection:

The pump is equipped with a chemical-resistant Viton® seal for enhanced durability. Periodically inspect the seal for any signs of wear or leaks. If a leak is detected, contact a qualified professional for replacement.

Winterization:

In colder climates, proper winterization is essential to prevent damage from freezing. Consult your pool professional for specific winterization procedures for your region.

Troubleshooting

This section provides solutions to common issues you might encounter with your TriStar VS 900 pump.

Problem	Possible Cause	Solution
Pump not starting	No power; tripped breaker; motor overload.	Check power supply and circuit breaker. Allow motor to cool if overloaded.
Low water flow	Clogged strainer basket; closed valve; air leak in suction line.	Clean strainer basket. Open all necessary valves. Check for air leaks.
Pump making unusual noise	Air in system; cavitation; worn bearings.	Bleed air from system. Ensure adequate water supply. Contact professional for bearing issues.
Water leaking from pump	Loose fittings; damaged seal; cracked housing.	Tighten fittings. Inspect and replace seal if damaged. Contact professional for housing issues.

For issues not listed or if solutions do not resolve the problem, please contact Hayward customer support or a certified pool professional.

Specifications

Key technical specifications for the Hayward TriStar VS 900 Variable-Speed Pump.

Model: TriStar VS 900
Brand: Hayward
Type: Variable-Speed Pool Pump
Energy Efficiency: Industry's best Weighted Energy Factor (WEF) of 12.9, ENERGY STAR rated.
Motor: Permanent magnet totally enclosed fan-cooled (TEFC) motor, dual-voltage.
Seal: Chemical-resistant Viton® seal.
Strainer Basket: No-rib design with see-through cover.
Connections: Standard union connections, side/rear conduit entries.
Color: Black
Material: Stainless Steel / Metal (as per specifications)
Power Source: Corded Electric
Item Weight: 52 Pounds
Maximum Flow Rate: 130 Gallons Per Minute (1.3E+2 GPM)
UPC: 610377328951
First Available: March 16, 2022

Warranty and Support

The Hayward TriStar VS 900 Variable-Speed Pump comes with a 3-year extended warranty, providing peace of mind regarding its durability and reliability.

For technical support, warranty claims, or to locate a certified pool professional for installation and service, please visit the official Hayward website or contact their customer service department.

Hayward Official Website: www.hayward-pool.com

Note: EXPERT LINE products, including this pump, are exclusively available and supported through your local pool professional.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.