OHM AV Learning Remote R850Z Instruction Manual

Introduction

Thank you for purchasing the OHM AV Learning Remote R850Z. This remote control is designed to simplify your home entertainment experience by allowing you to operate up to three AV devices with a single remote. It features a learning function for custom operations and a wide transmission range. Please read this manual carefully before use to ensure proper operation and to get the most out of your new remote.

Product Features

• Multi-Device Control: Capable of registering and operating up to 3 AV devices (TV, Tuner, BD/DVD).
• Learning Function: Allows you to teach the remote control operations from your original remote, even for functions not pre-registered. All buttons, including the F1-F5 customizable buttons, can be assigned.
• Memory Backup: Manufacturer code settings are retained even when changing batteries.
• Wide Transmission Range: Equipped with two signal transmission parts for broader coverage.
• Customizable Buttons: Features 5 convenient customizable buttons (F1-F5) for frequently used functions.

Image: Overview of the OHM AV Learning Remote R850Z, highlighting its multi-device control, learning function, memory backup, and wide transmission range.

Parts Identification

Familiarize yourself with the buttons and their functions on your remote control. Refer to the image below for a visual guide to all parts.

Image: Detailed diagram of the remote control with numbered labels for each button and component.

Key Button Functions:

• Tray Open/Close: Opens or closes the disc tray.
• Power: Turns the selected device on or off.
• TV/Tuner/BD Buttons: Selects the device to control.
• Number Buttons (0-12): For channel selection or numerical input.
• Volume (+/-): Adjusts the volume.
• Channel (+/-): Changes channels.
• Cursor/OK: Navigates menus and confirms selections.
• Play/Pause/Stop/Rewind/Fast Forward: Standard media playback controls.
• F1-F5: Customizable learning function buttons.
• Signal Transmitter: Infrared emitter for sending commands.
• Battery Compartment Cover: Access for battery installation.

Setup

1. Battery Installation

1. Remove the battery compartment cover on the back of the remote control.
2. Insert two AAA (UM-4) alkaline batteries, ensuring correct polarity (+/-).
3. Replace the battery compartment cover.

Note: Batteries are sold separately. Battery life is approximately 1 year with new alkaline batteries, but may vary depending on usage frequency.

2. Initial Setup: Setting Manufacturer Codes

To control your AV devices, you need to set the corresponding manufacturer code for each device type (TV, Tuner, or BD/DVD).

1. Identify the device you want to control (TV, Tuner, or BD/DVD).
2. Press and hold the corresponding device button (TV, Tuner, or BD) on the remote.
3. While holding the device button, enter the 3-digit manufacturer code for your device using the number buttons. Refer to the "Manufacturer Code List" section below.
4. Release the device button. The remote is now set for that device.
5. Test the remote by pressing various buttons (e.g., Power, Volume, Channel). If the device does not respond correctly, try the next code for your manufacturer from the list.

Note: The remote has a memory backup function, so manufacturer codes will be retained even if batteries are replaced.

Operating Instructions

1. Basic Operation

After setting the manufacturer codes, select the device you wish to control by pressing the corresponding device button (TV, Tuner, or BD). The remote will then send commands for that device.

2. Using the Learning Function

The learning function allows you to copy specific commands from your original remote control to any button on the OHM AV Learning Remote R850Z, including the F1-F5 customizable buttons. This is useful for functions not covered by the pre-programmed manufacturer codes.

1. Place the OHM AV Learning Remote R850Z and your original remote control facing each other, about 1-3 cm apart.
2. Enter learning mode. (The exact method to enter learning mode may vary. Please consult the full instruction manual for precise steps, as it typically involves holding a specific button or combination for a few seconds until an indicator light blinks.)
3. Once in learning mode:
   1. Press the button on the OHM remote that you want to program (e.g., F1, or any other button). The indicator light will change.
   2. Press the corresponding button on your original remote control. The indicator light on the OHM remote should blink rapidly or change color to confirm successful learning.
   3. Repeat for other buttons you wish to program.
   4. Exit learning mode (usually by pressing the same button or combination used to enter, or waiting for a timeout).

Note: For detailed instructions on entering and exiting learning mode, please refer to the complete instruction manual included with your product.

Manufacturer Code List

Use these codes to set up your remote for various TV, Tuner, and BD/DVD devices. If the first code does not work, try the next one listed for your brand.

Image: Manufacturer codes for various TV brands.

Image: Manufacturer codes for various Tuner and BD/DVD brands.

Important Compatibility Notes:

• This product was developed based on devices released by July 2018. Some devices or functions may not be operable.
• Devices released after August 2018 may also not be compatible.
• Not compatible with devices that do not have an infrared remote control.
• Even for manufacturers listed in the compatibility guide, there may be specific models or functions that are not supported.
• If a function on this product is not present on your device's original remote, that function cannot be used.
• This product is not compatible with car TVs, separated-type TVs (where display and receiver are separate), or PC monitors (including those with TV tuners).

Maintenance

• Wipe the remote control with a soft, dry cloth. Do not use abrasive cleaners or solvents.
• Avoid exposing the remote to direct sunlight, high temperatures, or high humidity.
• If the remote will not be used for an extended period, remove the batteries to prevent leakage.

Troubleshooting

• Remote not responding:
  • Check if the batteries are inserted correctly and are not depleted. Replace if necessary.
  • Ensure there are no obstructions between the remote and the device's infrared receiver.
  • Verify that the correct device button (TV, Tuner, BD) is selected.
  • Re-enter the manufacturer code for your device. Try alternative codes if the first one doesn't work.
• Specific functions not working:
  • Some functions may not be compatible with all devices, especially older models or those released after July 2018.
  • Use the learning function to program specific commands from your original remote to the OHM remote.
• Short operating distance:
  • Ensure batteries are fresh.
  • Operating distance may vary depending on room conditions and the device's IR receiver sensitivity.

Specifications

Warranty and Support

This product comes with a warranty. Please keep your delivery slip as it is required for warranty claims.

• Warranty Period: 1 year from the date of delivery.
• Proof of Purchase: The delivery slip is essential for warranty service.
• Coverage: Warranty is limited to use within Japan.
• For support or warranty claims, please contact your retailer or the OHM customer service department. Contact information can typically be found on the product packaging or the official OHM website.