Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of the GG Grand General 75849 4 Inches Fleet White/Clear 18 LED Surface Mount with Visor Bezel. This product is designed as a high-quality, DOT approved lighting solution for trucks, featuring 18 high-power 12V LEDs and a durable chrome twist, lock & go bezel for easy installation.
What's in the Box
- One (1) 4 Inches Fleet White/Clear 18 LED Surface Mount with Visor Bezel, 3 Wires
Safety Information
WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Always ensure the vehicle's power is disconnected before installation. Wear appropriate personal protective equipment (PPE) such as safety glasses and gloves. Consult a qualified professional if you are unsure about any installation steps.
Product Features
- Chrome twist, lock & go bezel for easy one-piece installation without a grommet.
- Dimensions: 5-3/4 inches diameter x 3/4 inches (H).
- Equipped with 18 high-power 12V LEDs.
- Waterproof design for enhanced durability.
Setup and Installation
This section outlines the steps for properly installing your GG Grand General LED surface mount light.
Tools Required:
- Wire Strippers/Crimpers
- Drill (if creating new mounting holes)
- Screwdriver (Phillips or Flathead, depending on mounting screws)
- Electrical Tape or Heat Shrink Tubing
- Multimeter (optional, for verifying voltage)
Installation Steps:
- Prepare Mounting Surface: Choose a flat, clean surface on your truck for mounting. Ensure there is sufficient space for the 5-3/4 inch diameter light.
Image: Front view of the GG Grand General 75849 LED light, showcasing its 18 clear LEDs and the reflective chrome bezel. This is the primary component for surface mounting.
- Drill Pilot Holes (if necessary): If not using existing holes, mark and drill appropriate pilot holes for the mounting screws. The light features a "twist, lock & go" bezel for easy installation, which typically involves securing the base and then twisting the bezel into place.
- Wiring Connections: The light comes with 3 wires.
- Identify the positive (+), negative (-), and auxiliary (if applicable, for dual-function lights) wires.
- Connect the positive wire to a 12V power source.
- Connect the negative wire to a suitable ground point on the vehicle chassis.
- Secure all connections using wire crimps, solder, and insulate with electrical tape or heat shrink tubing to prevent short circuits and ensure a waterproof seal.
Image: Angled view of the GG Grand General 75849 LED light, highlighting the clear lens and the chrome bezel with its integrated visor. This view helps in understanding the light's profile for mounting.
- Mount the Light: Secure the light assembly to the prepared surface using appropriate fasteners. Ensure it is firmly attached and does not wobble.
- Test Functionality: Once installed, reconnect the vehicle's power and test the light to ensure it functions correctly.
Operating Instructions
The GG Grand General 75849 LED light operates as a standard 12V lighting unit. Once properly wired and installed, its operation is controlled by the vehicle's electrical system, typically through a switch or integrated lighting circuit.
- Activation: The light will illuminate when power is supplied to its positive wire and the negative wire is grounded. This is usually controlled by the vehicle's existing lighting switch (e.g., marker lights, turn signals, or auxiliary light switch).
- Power Requirements: Ensure the power source is a stable 12V DC supply.
Maintenance
Minimal maintenance is required for the GG Grand General LED light due to its durable and waterproof design.
- Cleaning: Periodically clean the lens and bezel with a soft cloth and mild soap and water to remove dirt and debris. Avoid abrasive cleaners that could scratch the surface.
- Inspection: Regularly inspect the wiring connections for any signs of corrosion, fraying, or loose connections. Ensure the light remains securely mounted.
- LED Longevity: LEDs have a long lifespan and typically do not require replacement under normal operating conditions.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not illuminate. | No power supply; faulty wiring connection; blown fuse; incorrect grounding. | Check 12V power source with a multimeter. Verify all wire connections are secure and properly insulated. Inspect vehicle's fuse box for blown fuses. Ensure the ground connection is clean and solid. |
| Light flickers or is dim. | Loose connection; insufficient voltage; corroded wiring. | Tighten all connections. Check voltage at the light's input. Clean any corroded terminals or replace damaged wiring. |
| Water inside the lens. | Improper sealing during installation; damaged housing. | Ensure the light is properly sealed against the mounting surface. If housing is damaged, replacement may be necessary. |
Specifications
| Attribute | Detail |
|---|---|
| Brand | GG Grand General |
| Model Number | 75849 |
| Light Type | LED Surface Mount Light |
| LED Quantity | 18 High Power LEDs |
| Voltage | 12V |
| Color | White/Clear |
| Bezel Style | Chrome with Visor |
| Dimensions | 5-3/4" dia. x 3/4" (H) |
| Wiring | 3 Wires |
| Special Feature | Waterproof |
| Vehicle Service Type | Truck |
| Item Weight | 6.4 ounces |
| Country of Origin | Taiwan |
| UPC | 760479758498 |
Warranty and Support
For information regarding warranty coverage and technical support for your GG Grand General product, please refer to the manufacturer's official website or contact their customer service department directly. Keep your purchase receipt as proof of purchase for any warranty claims.
Manufacturer: Grand General
Website: www.grandgeneral.com