Introduction
This manual provides detailed instructions for the replacement of the brake spring (Part #11) on ProBasics 6" Aluminum Rollator models RLA6 and 1037. This component is crucial for the proper functioning of the rollator's braking system. Please read all instructions carefully before proceeding with the replacement.
Safety Information
- Always ensure the rollator is stable and cannot move during maintenance.
- If you are unsure about any step, consult a qualified technician.
- Keep small parts away from children.
- Wear appropriate safety gear, such as gloves, if necessary.
- After replacement, thoroughly test the brake system before using the rollator.
Tools Required
- Small Phillips head screwdriver
- Pliers (optional, for spring manipulation)
Installation Instructions: Brake Spring Replacement
Refer to the "ProBasics 6" Aluminum Rollator Exploded View" diagram and the "Parts List" below for visual guidance.
- Identify the Brake Assembly: Locate the brake assembly on your rollator. The brake spring (Part #11) is an integral part of this mechanism, typically found near the hand brake lever and the wheel.
- Disengage Brake: Ensure the brake is disengaged (not locked) before beginning.
- Access the Spring: Depending on your specific rollator model, you may need to partially disassemble the brake lever or wheel assembly to access the old brake spring. This usually involves unscrewing a few fasteners.
- Remove Old Spring: Carefully remove the old brake spring. Note its orientation and how it was attached, as the new spring will need to be installed in the same manner.
- Install New Spring: Position the new ProBasics Brake Spring (Part #11) in the same location and orientation as the old one. Ensure it is securely seated.
- Reassemble: Reassemble any parts that were removed to access the spring, ensuring all screws and fasteners are tightened appropriately.
- Test Brake Functionality: After reassembly, thoroughly test the brake system. Engage and disengage the brakes multiple times to ensure they operate smoothly and effectively. The wheels should lock firmly when the brake is engaged and spin freely when disengaged.
Maintenance
Regularly inspect the brake springs and other brake components for wear or damage. Replace any worn parts promptly to ensure safe operation of the rollator. Keep the brake mechanism clean and free of debris.
Troubleshooting
- Brake not engaging/disengaging properly: Re-check the installation of the brake spring. Ensure it is correctly seated and not obstructed. Verify that all other brake components are properly aligned and tightened.
- Brake feels loose: The spring might not be providing enough tension, or other parts of the brake assembly might be worn. Inspect the brake cable and lever for proper adjustment.
Specifications
- Part Name: Brake Spring
- Part Number: #11 (as per ProBasics diagram)
- Compatibility: ProBasics 6" Aluminum Rollator Models RLA6, 1037
- Material: (Not specified, but typically metal)
- Manufacturer: Compass Health
Parts Diagram and List
ProBasics 6" Aluminum Rollator Exploded View
This diagram illustrates the various components of the ProBasics 6" Aluminum Rollator, with each part assigned a number for easy identification. Part #11, the brake spring, is highlighted within the brake assembly.
ProBasics 6" Aluminum Rollator Parts List
This table provides a comprehensive list of parts for the ProBasics 6" Aluminum Rollator, correlating the figure numbers from the exploded view with their descriptions and official part numbers. Part #11 is listed as "ProBasics Rollator Brake Spring".
| Fig. | Description | Part No. |
|---|---|---|
| 1 | ProBasics 6" Alum. Rollator Left Hand Brake System (Includes brake spring & wheel contact) | X1RLA6MH01 |
| 2 | ProBasics 6" Alum. Rollator Right Hand Brake System (Includes brake spring & wheel contact) | X1RLA6MH02 |
| 3 | ProBasics 6" Alum. Rollator Backrest | X1RLA6MH03 |
| 4 | ProBasics 6" Alum. Rollator Front Caster Fork Assembly | X1RLA6MH04 |
| 5 | ProBasics 6" Alum. Rollator Replacement Pouch | X1RLA6MH05 |
| 6 | ProBasics 6" Alum. Rollator Caster w/Bearing (Front or Rear) | X1RLA6MH06 |
| 7 | ProBasics 6" Alum. Rollator Caster Axle Bolt w/Nut (Front or Rear) | X1RLA6MH07 |
| 8 | ProBasics 6" Alum. Rollator Replacement Seat | X1RLA6MH08 |
| 9 | ProBasics 6" Alum. Rollator Seat Clips and Screws | X1RLA6MH09 |
| 10 | ProBasics Brake Cable Ring | X1RLMH01 |
| 11 | ProBasics Rollator Brake Spring | X1RLMH02 |
| 12 | ProBasics Rollator Handle Height Adjustment Knob | X1RLMH03 |
| 13 | ProBasics Rollator Handle Grips, Pair | X1RLMH04 |
| 14 | ProBasics Rollator Caster Cap | X1RLMH05 |
| 15 | ProBasics Rollator Brake Wheel Contact | X1RLMH06 |
| 16 | ProBasics Rollator Backrest Fixator (L/R Set) | X1RLBL07 |
Warranty and Support
This brake spring is a replacement part for ProBasics rollators. For specific warranty information regarding this component or your rollator, please refer to the original rollator's user manual or contact ProBasics customer support directly. Keep your purchase receipt for warranty claims.
For further assistance or to purchase additional replacement parts, please visit the official ProBasics website or contact their authorized dealers.
