Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Signature Hardware Pendleton 1.2 GPM Widespread Bathroom Faucet. Please read all instructions carefully before beginning installation to ensure proper function and longevity of the product. Keep this manual for future reference.
Safety Information
- Always turn off the main water supply before installing or performing any maintenance on the faucet.
- Wear appropriate personal protective equipment, such as safety glasses, during installation.
- If you are unsure about any part of the installation process, consult a qualified plumber.
- Ensure all connections are secure to prevent leaks.
- Do not overtighten components, as this may cause damage.
Included Components
Verify that all components are present before beginning installation:
- Faucet Spout Assembly
- Hot and Cold Handle Assemblies
- Pop-Up Drain Assembly
- Mounting Hardware
- Gaskets and Seals
Image: The Signature Hardware Pendleton Widespread Bathroom Faucet in Polished Nickel, showing the spout and two lever handles, along with the pop-up drain assembly.
Installation Instructions
This faucet is designed for widespread installation on a 3-hole sink with 8-inch centers.
- Prepare the Sink: Ensure the sink holes are clean and free of debris. Turn off the water supply at the main shut-off valve.
- Install Handle Assemblies: Insert the hot and cold handle assemblies into the outer holes of the sink. Secure them from underneath with the provided washers and nuts. Ensure the handles are oriented correctly.
- Install Faucet Spout: Place the faucet spout assembly into the center hole of the sink. Secure it from underneath with the provided mounting hardware, ensuring a tight seal with the gasket.
- Connect Water Lines: Attach the hot and cold water supply lines to the corresponding handle assemblies and then to the main water supply. Use thread sealant tape on all threaded connections.
- Install Pop-Up Drain: Follow the separate instructions provided with the pop-up drain assembly for proper installation into the sink drain opening. Connect the lift rod (if applicable) to the faucet spout.
- Test for Leaks: Slowly turn on the main water supply and check all connections for leaks. Run water through the faucet for a few minutes to flush out any debris.
Operating Instructions
The Pendleton faucet features dual lever handles for precise control of water flow and temperature.
- Water Flow: Lift the lever handles to increase water flow and push them down to decrease or stop flow.
- Temperature Control: Rotate the left handle for hot water and the right handle for cold water. Adjust both handles to achieve the desired water temperature.
- Flow Rate: This faucet has a maximum flow rate of 1.2 Gallons Per Minute (GPM).
Care and Maintenance
Proper care will maintain the finish and performance of your faucet.
- Cleaning: Clean the faucet regularly with a soft cloth and mild soap. Rinse thoroughly with clean water and dry immediately to prevent water spots.
- Avoid Harsh Cleaners: Do not use abrasive cleaners, harsh chemicals, or polishes containing alcohol, ammonia, or bleach, as these can damage the Polished Nickel finish.
- Aerator Maintenance: Periodically unscrew the aerator from the spout and clean any mineral deposits or debris to maintain optimal water flow.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Low Water Flow | Clogged aerator; partially closed shut-off valve; debris in water lines. | Clean or replace aerator; ensure shut-off valves are fully open; flush water lines. |
| Leaks from Faucet Base | Loose mounting nuts; damaged gasket. | Tighten mounting nuts; inspect and replace gasket if damaged. |
| Dripping Faucet | Worn cartridge. | Contact customer support for a replacement cartridge. |
Specifications
- Brand: Signature Hardware
- Model Name: Pendleton
- Model Number: SHWSCPT807PN
- Part Number: 447898
- Material: Brass
- Finish Type: Polished Nickel
- Number of Handles: 2
- Mounting Type: Deck Mount
- Hole Count: 3
- Maximum Flow Rate: 1.2 Gallons Per Minute
- Spout Reach: 5.13 Inches
- Product Dimensions: 17.13"D x 10.63"W x 3.15"H
- Item Weight: 7 Pounds
- Special Feature: Rust Resistant
- Included Components: Faucet, Pop-Up Drain
Warranty Information
This Signature Hardware faucet is covered under a 25-year limited warranty. This warranty covers defects in material and workmanship under normal use. For specific terms and conditions, please refer to the official Signature Hardware warranty documentation or contact customer support.
Customer Support
For technical assistance, replacement parts, or warranty claims, please visit the official Signature Hardware website or contact their customer service department. Have your model number (SHWSCPT807PN) and purchase date available when contacting support.