1. Introduction
This instruction manual provides essential information for the safe and effective installation, operation, and maintenance of the AirXHeat 1011632 ICP Furnace Draft Inducer/Exhaust Vent Venter Motor. This component is designed as a direct replacement for specific Fasco models in ICP furnace systems. Please read this manual thoroughly before proceeding with installation or service to ensure proper function and safety.
2. Safety Information
WARNING: Risk of Electric Shock and Injury.
- Always disconnect power to the furnace at the main circuit breaker or fuse box before attempting any installation, maintenance, or repair.
- Installation and servicing should only be performed by a qualified HVAC technician or licensed electrician.
- Ensure all wiring connections are secure and comply with local electrical codes.
- Wear appropriate personal protective equipment (PPE), including safety glasses and gloves.
- Do not operate the furnace if the draft inducer motor is damaged or not functioning correctly.
3. Package Contents
Verify that all components are present and undamaged upon opening the package:
- 1 x AirXHeat 1011632 ICP Furnace Draft Inducer/Exhaust Vent Venter Motor
- Instruction Manual (this document)
4. Product Overview
The AirXHeat 1011632 is a replacement draft inducer motor designed for ICP furnace systems. Its primary function is to draw combustion gases from the furnace heat exchanger and vent them safely out of the building, ensuring proper airflow for efficient and safe combustion. This motor is a critical safety component, as it proves the furnace's ability to vent exhaust gases before allowing the main burner to ignite.
5. Specifications
| Brand | AirXHeat |
| Model Number | 1011632 |
| Manufacturer | AirXHeat |
| UPC | 301638973705 |
| ASIN | B086N2R6LJ |
| Compatible Models (Where Used) | NDP6050FBA1, NDP6050FBB1, NDP6050FBG1, NDP6075FBA1, NDP6075FBB1, NDP6075FBB2, NDP6075FBG1, NDP6100HFA1, NDP6100HFB1, NDP6100HFG1, NDP6125KJA1, NDP6125KJB1, NDP6125KJB2, NDP6125KJG1, NTP6050FBA1, NTP6050FBB1, NTP6050FBG1, NTP6075GFA1, NTP6075GFB1, NTP6075GFB2, NTP6075GFG1, NTP6100GFA1, NTP6100GFB1, NTP6100GFG1, NTP6100KJA1, NTP6100KJB1, NTP6100KJG1, NTP6125KJA1, NTP6125KJB1, NTP6125KJB2, NTP6125KJG1, NTV6050FBA1, NTV6050FBG1, NTV6075GFA1, NTV6075GFG1, NTV6100KJA1, NTV6100KJG1, NTV6125KJA1, NTV6125KJG1, TDE050B12A1, TDE050B12B1, TDE050B12G1, TDE075B12A1, TDE075B12B1, TDE075B12B2, TDE075B12G1, TDE100F16A1, TDE100F16B1, TDE100F16G1, TDE125J20A1, TDE125J20B1, TDE125J20B2, TDE125J20G1, TNE050B12A1, TNE050B12B1, TNE050B12G1, TNE075F14A1, TNE075F14B1, TNE075F14B2, TNE075F14G1, TNE100F14A1, TNE100F14B1, TNE100F14G1, TNE100J20A1, TNE100J20B1, TNE100J20G1, TNE125J20A1, TNE125J20B1, TNE125J20B2, TNE125J20G1, VNE050B12A1, VNE050B12G1, VNE075F14A1, VNE075F14G1, VNE100J20A1, VNE100J20G1, VNE125J20A1, VNE125J20G1 |
6. Installation/Setup
Professional installation by a qualified HVAC technician is strongly recommended for this component.
- Disconnect Power: Turn off all electrical power to the furnace at the main service panel. Verify power is off using a voltage tester.
- Access Inducer Motor: Locate the existing draft inducer motor on your furnace. This typically involves removing access panels.
- Disconnect Wiring: Carefully disconnect the electrical wiring from the old motor. Note the position and color of each wire for correct re-connection. Taking a photograph can be helpful.
- Remove Old Motor: Unbolt or unfasten the old draft inducer motor from its mounting bracket or furnace housing. Be prepared for potential residual moisture or debris.
- Inspect Area: Clean any debris, rust, or corrosion from the mounting surface and exhaust pathway.
- Install New Motor: Position the AirXHeat 1011632 motor in the same orientation as the old one. Secure it firmly using the appropriate bolts or fasteners. Ensure a tight seal if a gasket is present.
- Connect Wiring: Reconnect the electrical wiring to the new motor, matching the connections noted in step 3. Double-check all connections for security.
- Verify Venting: Ensure that the exhaust vent pipe is clear and properly connected to the inducer motor's outlet.
- Restore Power & Test: Replace all access panels. Restore power to the furnace. Initiate a call for heat and observe the new draft inducer motor's operation. Listen for unusual noises and check for proper exhaust venting.
7. Operating Principles
The draft inducer motor is an integral part of a modern furnace's safety and efficiency system. When the thermostat calls for heat, the furnace control board first activates the draft inducer motor. This motor creates a negative pressure (draft) within the heat exchanger, pulling in fresh air for combustion and expelling exhaust gases. A pressure switch monitors this draft; if sufficient draft is established, the pressure switch closes, signaling the control board that it is safe to ignite the main burners. If the draft is insufficient, the furnace will not ignite, preventing the accumulation of dangerous combustion gases within the home.
8. Maintenance
Regular inspection and maintenance can extend the life of your draft inducer motor and ensure safe furnace operation. It is recommended to have your furnace, including the draft inducer motor, inspected annually by a qualified HVAC technician.
- Visual Inspection: Periodically check the motor for signs of wear, corrosion, or damage. Ensure all connections are secure.
- Cleanliness: Keep the area around the motor and the exhaust vent clear of obstructions and debris. Dust and lint can accumulate and affect performance.
- Noise Monitoring: Pay attention to any changes in the motor's operating sound. Unusual noises may indicate a developing issue.
9. Troubleshooting
If your furnace is experiencing issues related to the draft inducer motor, consider the following common problems and potential solutions. Always disconnect power before inspecting components.
| Problem | Possible Cause | Solution |
|---|---|---|
| Motor does not start or furnace does not ignite. | No power, faulty wiring, clogged vent, faulty pressure switch, motor failure. | Check circuit breaker. Verify wiring connections. Inspect vent for blockages. Consult an HVAC technician to test pressure switch and motor. |
| Motor runs but furnace does not ignite. | Faulty pressure switch, clogged vent, restricted exhaust. | Inspect vent for blockages. Consult an HVAC technician to test or replace the pressure switch. |
| Unusual noises (grinding, squealing) from motor. | Worn bearings, impeller obstruction, motor nearing end of life. | Disconnect power and inspect for obstructions. If noise persists, motor replacement may be necessary. Consult an HVAC technician. |
For complex issues or if you are unsure about any troubleshooting steps, contact a certified HVAC professional.
10. Warranty and Support
For information regarding warranty coverage, technical support, or replacement parts for your AirXHeat 1011632 ICP Furnace Draft Inducer/Exhaust Vent Venter Motor, please refer to the manufacturer's official website or contact their customer service department directly. Keep your purchase receipt and model number handy when contacting support.