VIVOSUN 5-in-1 Digital PH Meter User Manual

Product Overview

The VIVOSUN 5-in-1 Digital PH Meter is a versatile instrument designed for accurate measurement of various water quality parameters. This device allows you to measure pH, Total Dissolved Solids (TDS), Electrical Conductivity (EC), Salinity, and Temperature. It is an essential tool for maintaining optimal conditions in hydroponics, home drinking water, pools, and aquariums.

Figure 1: VIVOSUN 5-in-1 Digital PH Meter with protective cap removed, displaying a reading.

Key features include a backlight screen for easy reading, IP67 waterproof rating for durability, and automatic temperature compensation (ATC) to ensure accurate readings regardless of liquid temperature. The meter is designed for ease of use with simple button controls for mode switching and calibration.

Figure 2: Diagram illustrating the components of the VIVOSUN 5-in-1 PH Meter, including the battery case, screen display, ON/OFF button, HOLD/TEMP button, MODE/CAL button, protective cap, max immersion line, and test probe.

Setup

Battery Installation

The VIVOSUN 5-in-1 Digital PH Meter requires 3 cell batteries (not included). To install or replace batteries:

1. Unscrew the battery cap at the top of the meter.
2. Insert 3 cell batteries, ensuring correct polarity.
3. Securely screw the battery cap back on.

Initial Preparation

Before first use, or after prolonged storage, it is recommended to rinse the electrode with distilled water and gently blot dry. Ensure the protective cap is removed before use.

Operating Instructions

The meter features a simple three-button interface: ON/OFF, HOLD/TEMP, and MODE/CAL.

Power On/Off

• Press the ON/OFF button to turn the meter on.
• Press and hold the ON/OFF button for a few seconds to turn the meter off. The meter also features an auto-shut off function after approximately 5 minutes of inactivity to conserve battery life.

Switching Measurement Modes

After powering on, the meter defaults to pH mode. To cycle through the different measurement modes (pH, TDS, EC, Salinity, Temperature), press the MODE/CAL button repeatedly.

Figure 3: Visual guide for switching between pH, TDS, EC, Salinity, and Temperature modes using the MODE/CAL button.

Taking Measurements

1. Ensure the meter is in the desired measurement mode.
2. Immerse the electrode of the meter into the liquid up to the maximum immersion line.
3. Gently stir the meter to remove any air bubbles and allow the reading to stabilize.
4. Read the stable value displayed on the screen.

Hold Function

Press the HOLD/TEMP button to freeze the current reading on the display. Press it again to release the hold and resume live readings.

Temperature Unit Switching

While in any measurement mode, press and hold the HOLD/TEMP button for a few seconds to switch between Celsius (°C) and Fahrenheit (°F) temperature units.

Specific Measurement Details:

• pH Measurement: Measures the acidity or alkalinity of a solution (0.00-14.00pH).
  

  Figure 4: PH Level chart showing common substances and their typical pH ranges.
• TDS (Total Dissolved Solids) Measurement: Measures the concentration of dissolved solid particles in a solution. Range: 0-1000ppm; 10.1-200.0ppt.
  

  Figure 5: TDS in PPM chart indicating water quality levels based on dissolved solids.

• EC (Electrical Conductivity) Measurement: Measures the electrical conductivity of a solution, indicating the concentration of ions. Range: 0-9990µS/cm; 10.01-19.99 mS/cm; 20.1-400.0 mS/cm.
  

  Figure 6: EC measurement in a hydroponic setup, showing typical ranges and resolution.

• Salinity Measurement: Measures the salt content of a solution. Range: 0.01-25.00 %; 0-10000 ppm; 10.1-200.0 ppt. Salinity is converted through EC.
  

  Figure 7: Salinity measurement being performed in an aquatic environment, highlighting the high accuracy electrode.
• Temperature Measurement: Measures the temperature of the solution. Range: 0.1-60℃ / 32.1-140℉.

Figure 8: Examples of common applications for the VIVOSUN 5-in-1 PH Meter, including swimming pools, hydroponics, deep water culture (DWC), and aquariums.

Maintenance

Calibration

The meter features automatic three-point calibration for pH (pH 4.00, pH 6.86, and pH 9.18). Regular calibration ensures accuracy.

1. Prepare the calibration buffer solutions (pH 4.00, 6.86, 9.18).
2. Turn on the meter and switch to pH mode.
3. Immerse the electrode in the 6.86 pH buffer solution.
4. Press and hold the MODE/CAL button until "CAL" appears on the screen. The meter will automatically recognize the solution and calibrate.
5. Rinse the electrode with distilled water and repeat the process for pH 4.00 and pH 9.18 solutions.

Note: EC and TDS calibration may require specific solutions not included with the meter. Refer to specialized guides for advanced calibration.

Cleaning and Storage

• After each use, rinse the electrode thoroughly with distilled water to prevent contamination.
• Gently blot the electrode dry with a clean, soft cloth. Do not rub.
• Always replace the protective cap to keep the electrode moist and protected.
• Store the meter in a cool, dry place away from direct sunlight and extreme temperatures.

Troubleshooting

Specifications

Warranty and Support

VIVOSUN products are designed for reliability and performance. For warranty information and customer support, please refer to the official VIVOSUN website or contact their customer service directly. Keep your purchase receipt for warranty claims.

You can visit the VIVOSUN store on Amazon for more products and information: VIVOSUN Amazon Store