Reverie RC-WM-103 Adjustable Bed Remote Control Instruction Manual

Introduction

This manual provides essential instructions for the setup, operation, and maintenance of your Reverie RC-WM-103 Replacement Remote Control for adjustable bed bases. This remote is designed as an exact OEM replacement for Reverie 5i, 5D, 7S, R400, or 4M adjustable bed bases. Please review this manual thoroughly to ensure proper functionality and compatibility.

Important: Ensure your original remote matches the appearance of this remote exactly, including the logo, for guaranteed compatibility. This remote is not compatible with old Tempurpedic bases, even if buttons appear similar.

Safety Information

• Keep the remote control away from water and excessive moisture.
• Do not expose the remote to extreme temperatures.
• Avoid dropping the remote or subjecting it to strong impacts.
• Keep batteries out of reach of children.
• Dispose of old batteries responsibly according to local regulations.

Setup

1. Unpacking

Carefully remove the remote control from its packaging. Inspect for any visible damage. If damage is present, contact your retailer.

2. Battery Installation

The remote control requires two AAA batteries (not included). To install:

1. Locate the battery compartment cover on the back of the remote.
2. Slide the cover off in the direction indicated by the arrow.
3. Insert two AAA batteries, ensuring the correct polarity (+ and -) as marked inside the compartment.
4. Replace the battery compartment cover until it clicks securely into place.

3. Pairing/Syncing the Remote Control

To establish communication between your new remote and the adjustable bed base, follow these pairing instructions:

1. Ensure the bed base is plugged into a working power outlet.
2. Locate the control box under your adjustable bed base. This box typically has a small button, often labeled "PAIR," "LEARN," or "SYNC." It might be recessed and require a pen tip to press.
3. Press and hold the pairing button on the control box for approximately 3 seconds. The indicator light on the control box should begin to flash.
4. Immediately after the light starts flashing, press and hold any button on your new remote control (e.g., "HEAD UP" or "FLAT") for 3-5 seconds.
5. Release the button on the remote. The indicator light on the control box should stop flashing, indicating successful pairing.
6. Test the remote by pressing various function buttons to ensure the bed base responds correctly.

Note: If pairing is unsuccessful, repeat the steps. Some older bed bases may require pressing the pairing button on the control box with a pen tip.

Operating the Remote Control

The Reverie RC-WM-103 remote control provides intuitive control over your adjustable bed's functions. Refer to the image below for button layout and descriptions.

This image displays the Reverie RC-WM-103 remote control. On the left is the older black version, and on the right is the new gray OEM version, which is the replacement model. Both remotes feature buttons for head and foot adjustments, lift, massage, and preset positions.

Button Functions:

• HEAD UP/DOWN Arrows: Adjusts the head section of the bed upwards or downwards.
• FOOT UP/DOWN Arrows: Adjusts the foot section of the bed upwards or downwards.
• LIFT: Activates a quick lift function for the entire bed or a specific preset.
• FLAT: Returns the bed to a completely flat position.
• MASSAGE (HEAD/FOOT): Activates or adjusts massage functions for the head or foot sections.
• MASSAGE (WAVE/PULSE/STEADY): Controls different massage modes.
• PRESET Buttons (1, 2, 3): Recalls pre-programmed favorite positions.
• ZERO GRAVITY (if present): Elevates the head and foot to a position that mimics weightlessness, reducing pressure on the body.

Maintenance

Cleaning:

Wipe the remote control with a soft, dry cloth. Do not use liquid cleaners or abrasive materials, as they may damage the surface or internal components.

Battery Replacement:

Replace batteries when the remote's response becomes sluggish or stops working. Always replace both batteries at the same time with new ones of the same type (AAA). Do not mix old and new batteries or different battery types.

Troubleshooting

Remote Not Responding:

• Check Batteries: Ensure batteries are correctly installed and not depleted. Replace if necessary.
• Re-Pair Remote: Follow the "Pairing/Syncing the Remote Control" steps in the Setup section to re-establish connection.
• Power Supply: Verify that the adjustable bed base is properly plugged into a working power outlet.
• Obstructions: Ensure there are no objects blocking the signal path between the remote and the bed base.

Bed Base Not Moving Smoothly:

• Check for Obstructions: Ensure no objects are under or around the bed base that could impede its movement.
• Power Cycle: Unplug the bed base from the power outlet for 30 seconds, then plug it back in.

If problems persist after attempting these troubleshooting steps, contact customer support.

Specifications

Warranty and Support

For warranty information or technical assistance, please contact the retailer or manufacturer directly. Keep your purchase receipt as proof of purchase.

For further assistance, you may visit the Reverie Adjustable Bed Remotes store on Amazon or refer to the contact information provided with your original bed base documentation.