wonline 36-inch Black Bathroom Vanity and Sink Combo Instruction Manual

1. Introduction

This manual provides detailed instructions for the assembly, installation, and maintenance of your wonline 36-inch Black Bathroom Vanity and Sink Combo. Please read all instructions carefully before beginning assembly to ensure safe and correct installation. Keep this manual for future reference.

2. Important Safety Information

• Always unplug and turn off the faucet before any maintenance or assembly.
• Be cautious of fingers when using soft-closing doors.
• Ensure the cabinet is securely mounted to the wall to prevent tipping.
• Keep the area around the cabinet clear of flammable materials.
• Always follow the installation instructions carefully to avoid injury or damage.

3. Package Contents

Your vanity set is shipped in three separate boxes. Please verify all components are present before beginning assembly.

• 2 x Vanity Cabinets (Large and Small)
• 2 x Countertops
• 1 x Ceramic Vessel Sink
• 1 x Mirror
• 1 x Chrome Faucet
• 1 x Chrome Pop-Up Drain
• Installation Hardware (screws, bolts, felt pads, drawer slides, hinges, etc.)
• Installation Instruction Manual

4. Tools Required

The following tools are recommended for assembly:

• Toolbox
• Drill (5*70mm)
• Open-end wrench
• Screwdriver (6*125mm)
• Utility Knife
• Dual-purpose screwdriver

5. Assembly Instructions

Follow these steps for proper assembly. Refer to the embedded video for visual guidance.

5.1. Unpacking and Preparation

• Place furniture boxes with arrows facing up to facilitate unpacking.
• Use a utility knife to gently cut along the edges of the packaging where the adhesive tape is located. Avoid excessive force to prevent scratching the furniture veneer.
• Open the packaging, remove the component boxes and furniture panels. Handle them carefully to avoid scratching the veneer.
• Place furniture panels on top of protective layers such as unpacked cardboard or carpets.
• Arrange the panels by category for easy access during assembly.
• Open the hardware box, take out the screws and other parts, and place them into the hardware accessory box.

5.2. Assemble Cabinet Frame

• Install cam bolts (hardware A) on panels No.1, No.3, No.6, and No.8.
• Install L-brackets (hardware L1) on panels No.3 and No.8, and secure with screws (hardware L2).
• Install felt pads (hardware N) at the designated locations on the bottom of panels No.1, No.3, No.6, and No.8.
• Install drawer slides (hardware CL and CR) on panels No.7 and No.11 respectively, and secure with screws (hardware H).
• Install cam bolts (hardware A) on panels No.2, No.7, and No.11.
• Flip panel No.11 and install cam bolts (hardware A) on it.
• Install wooden dowels (hardware C) on panels No.2 and No.7.
• Join panel No.6 and panel No.8 with panel No.7, and join panel No.1 and panel No.3 with panel No.2, securing them with cam locks (hardware B).
• Install back support (hardware K) on panel No.4 and secure it with bolts (hardware R).
• Install wooden dowels (hardware C) on panel No.2 and panel No.4.
• Install panels No.4, No.5, No.9, and No.10 on panel No.2, securing them with cam locks (hardware B).
• Install wooden dowels (hardware C) on panel No.13.
• Install panel No.14 and panel No.15 on panel No.13, securing them with cam locks (hardware B).
• Install wooden dowels (hardware C) on panel No.13.
• Install panel No.11 on panel No.13 and secure it with screws (hardware F).
• Install wooden dowels (hardware C) at the designated locations.
• Assemble the two main cabinet parts and secure them with cam locks (hardware B).
• Install the two No.12 boards at the designated locations.
• Install wooden dowels (hardware C) at the designated locations.
• Install the No.7 board and secure it with cam locks (hardware B).

5.3. Assemble Drawers

• Install cam bolts (hardware A) on the No.22 board.
• Install the No.21, No.18, and No.20 boards on the No.22 board and secure them with cam locks (hardware B).
• Install the No.19 board at the designated location and secure it with screws (hardware L).
• Install the drawer slides (hardware DL and DR) at the locations shown in the video, securing them with screws (hardware H).
• Install the three assembled drawers into the cabinet.

5.4. Install Sliding Door

• Install nuts (hardware P) and bolts (hardware R) on panel No.16.
• Install magnetic contacts (hardware Q) on panel No.16.
• Install the handle (hardware M) on panel No.16, securing it with bolts (hardware S).
• Install panel No.16 at the location shown in the video.

5.5. Install Sink and Faucet

• Open the packaging of the ceramic basin.
• Assemble the faucet and pop-up drain according to their individual instructions.
• Install the assembled faucet and pop-up drain into the ceramic sink.
• Place the ceramic sink onto the vanity cabinet.

5.6. Install Mirror

• Open the packaging of the mirror.
• Flip panel No.17 to the back.
• Install the hardware U on panel No.17, securing it with screws (hardware G).
• Hang the mirror on a suitable position on the wall above the vanity.

5.7. Final Adjustments

• Check if the cabinet is wobbly. If it is unstable, adjust the screws promptly.
• If the cabinet is stable, install the hardware J (stickers) as shown in the video to cover screw holes.

6. Product Specifications

7. Care and Maintenance

• Cleaning: Use a soft, damp cloth and mild soap for regular cleaning. Avoid abrasive cleaners or harsh chemicals that can damage the finish or ceramic.
• Spills: Wipe up spills immediately to prevent staining, especially on the countertop and wood surfaces.
• Wood Care: Avoid prolonged exposure to moisture. Periodically check and tighten any loose hardware.
• Ceramic Sink: Clean with non-abrasive cleaners. Do not use steel wool or harsh scouring pads.
• Mirror: Clean with a glass cleaner and a soft, lint-free cloth.

8. Troubleshooting

• Wobbly Cabinet: Ensure all cam locks and screws are fully tightened. Check if the vanity is on a level surface; adjust feet if applicable.
• Drawer Malfunction: Check that drawer slides are correctly installed and free of obstructions. Ensure screws securing the slides are tight.
• Leaking Faucet/Drain: Verify all plumbing connections are tight and that plumber's tape or sealant was used where recommended. Check for damaged O-rings or washers.
• Door Misalignment: Adjust the hinges using the adjustment screws (refer to hinge adjustment instructions if provided separately).

9. Warranty and Support

For warranty information or technical support, please refer to the documentation included with your purchase or contact wonline customer service directly. Keep your purchase receipt as proof of purchase.