1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Speakman Kubos SLV-1330-UNI EasyInstall Universal Shower and Tub Combination. This system is designed to refresh your shower and tub area without requiring extensive behind-the-wall valve replacements or tile work. Please read all instructions carefully before beginning installation or operation to ensure proper function and safety.
Image 1.1: The Speakman Kubos shower and tub combination installed in a modern bathroom setting.
2. Safety Information
Observe the following safety precautions during installation and use:
- Always turn off the main water supply before beginning any plumbing work.
- Wear appropriate personal protective equipment, such as safety glasses, during installation.
- If you are unsure about any part of the installation process, consult a qualified plumber.
- Ensure all connections are secure to prevent leaks.
- This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm (Proposition 65 warning). Wash hands after handling.
3. Package Contents
Verify that all components are present before beginning installation:
- Showerhead
- Shower arm
- Universal valve trim
- Tub spout
- Mounting hardware
4. Setup and Installation
The Speakman Kubos EasyInstall system is designed for straightforward replacement of existing shower and tub trim. This system is compatible with many common valve brands and models, including Kohler Rite-Temp K-304-KS, Moen PosiTemp 62370, Delta R10000-UNWS, and Symmons 46-2-X-BODY Temptrol valve.
4.1. Preparation
- Turn off the main water supply to your home.
- Remove the existing showerhead, shower arm, valve trim, and tub spout.
- Clean the surrounding wall area to ensure a proper seal for the new components.
4.2. Installation Steps
- Install Shower Arm: Apply plumber's tape to the threaded end of the new shower arm. Thread the shower arm into the wall fitting and tighten securely.
- Attach Showerhead: Thread the Kubos showerhead onto the shower arm. Hand-tighten, then use a wrench to tighten an additional quarter turn. Do not overtighten.
- Install Tub Spout: Follow the instructions provided with the tub spout for your specific plumbing configuration (e.g., slip-on or threaded connection). Ensure a tight seal to prevent leaks.
- Install Valve Trim: Refer to the specific instructions for the universal valve trim, as installation may vary slightly depending on your existing valve body. Generally, this involves aligning the trim plate and handle with the valve stem and securing it with the provided screws.
Image 4.1: Close-up view of the Speakman Kubos square shower head.
5. Operating Instructions
The Kubos Exhilaration Shower Head features multiple spray settings for a customized shower experience.
5.1. Water Flow Control
- Turn the valve handle to the left to increase water temperature and to the right to decrease it.
- Pull the handle outwards to turn on the water flow and push it inwards to turn it off.
5.2. Shower Head Spray Settings
The shower head offers four distinct spray settings and a pause mode. Rotate the spray face or a designated lever on the shower head to cycle through the following options:
- Massage: A focused, invigorating spray.
- Rain: A gentle, wide coverage spray.
- Satin: A soft, aerated spray.
- Speakman Reaction: A powerful, full-coverage spray.
- Pause Mode: Temporarily reduces water flow to a trickle, useful for lathering or shaving without changing temperature settings.
Image 5.1: Diagram illustrating the four unique spray settings available on Speakman Exhilaration shower heads.
Image 5.2: The Speakman Kubos shower head actively spraying water.
6. Maintenance
Regular cleaning will help maintain the appearance and performance of your Speakman Kubos shower and tub combination.
- Cleaning the Finish: Clean the polished chrome finish with a soft, damp cloth and mild soap. Avoid abrasive cleaners, harsh chemicals, or scouring pads, as these can damage the finish.
- Cleaning the Shower Head Nozzles: If mineral deposits accumulate in the shower head nozzles, gently rub the rubber nozzles with your finger or a soft brush to dislodge them. For stubborn deposits, a solution of equal parts white vinegar and water can be used. Soak the shower head (if removable) or apply the solution to the nozzles, let it sit for a few minutes, then rinse thoroughly.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Low water pressure from shower head. |
|
|
| Leaks around connections. |
|
|
| Water temperature inconsistent. |
|
|
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | SLV-1330-UNI |
| Brand | Speakman |
| Finish Type | Polished Chrome |
| Material | Plastic, Zinc, Brass (handle) |
| Number of Handles | 1 |
| Mounting Type | Wall Mount |
| Item Weight | 1.6 Pounds |
| Included Components | Showerhead, shower arm, universal valve trim, tub spout |
| UPC | 671252158452 |
| GTIN | 671252158452 |
8.1. Allowed Flow Rate by State
Please note that water flow rates may be regulated by state or local codes. The following table provides general guidance on allowed flow rates:
Image 8.1: Table detailing allowed showerhead flow rates (GPM) by state.
9. Warranty and Support
Manufacturer Warranty: This product is covered by a Limited Lifetime Warranty from Speakman. For specific terms and conditions, please refer to the warranty documentation included with your purchase or visit the official Speakman website.
Customer Support: For technical assistance, replacement parts, or warranty claims, please contact Speakman customer service. Contact information can typically be found on the Speakman website or on the product packaging.