YUSTDA TNS30W-xy

YUSTDA AC-DC Power Adapter TNS30W-xy User Manual

Model: TNS30W-xy

1. Introduction

This manual provides instructions for the safe and efficient use of your YUSTDA AC-DC Power Adapter, model TNS30W-xy. This power adapter is designed to provide reliable power to compatible Yaesu and Standard Horizon radio models. Please read this manual thoroughly before use and retain it for future reference.

2. Safety Information

To ensure safe operation and prevent damage, observe the following safety precautions:

  • Overload Protection: The adapter features built-in overload protection. Do not exceed the specified wattage (45 watts).
  • Over-charge/discharge Protection: Designed to protect connected devices from over-charging or over-discharging.
  • Overheating Protection: Equipped with a smart chip to prevent overheating. Ensure adequate ventilation around the adapter during use.
  • Short-circuit Protection: Provides protection against short circuits.
  • Anti-Interference: Constructed with isolation materials to minimize interference.
  • Use only with devices listed as compatible. Refer to the "Specifications" section for a list of compatible models.
  • Do not expose the adapter to water, moisture, or extreme temperatures.
  • Do not disassemble or attempt to repair the adapter. Contact qualified personnel for service.
  • Keep out of reach of children.
  • Unplug the adapter from the power outlet when not in use for extended periods.

Caution: Risk of electric shock. Dry location use only. For indoor use only.

3. Package Contents

Verify that all items are present in the package:

  • 1 x YUSTDA AC-DC Power Adapter (Model: TNS30W-xy)

4. Setup

Follow these steps to set up your power adapter:

  1. Inspect the Adapter: Before connecting, visually inspect the adapter and its cable for any signs of damage. Do not use if damaged.
  2. Connect to Device: Plug the barrel connector end of the adapter cable into the charging port of your compatible Yaesu or Standard Horizon radio.
  3. Connect to Power Outlet: Insert the AC plug of the adapter into a standard wall power outlet (100-240VAC, 50/60Hz).
  4. Verify Connection: Ensure both connections are secure. The device should indicate that it is receiving power or charging.
YUSTDA AC-DC Power Adapter with cable
Figure 4.1: The YUSTDA AC-DC Power Adapter with its integrated power cable and barrel connector.

The image above shows the YUSTDA AC-DC Power Adapter, highlighting its compact design and the attached power cord with a barrel connector. This is the unit you will connect to your radio and a wall outlet.

YUSTDA AC-DC Power Adapter plugged into a power strip
Figure 4.2: The YUSTDA AC-DC Power Adapter connected to a power strip, demonstrating typical usage.

This image illustrates the power adapter plugged into a standard power strip, ready to supply power to a connected device. Ensure the power strip or wall outlet is easily accessible.

5. Operating Instructions

Once the adapter is properly connected to both the power outlet and your compatible radio, it will begin to supply power or charge the device's battery. No further user interaction is typically required for basic operation.

  • The adapter is designed for continuous operation within its specified voltage and wattage limits.
  • Monitor your device's charging indicator to confirm proper function.
  • Disconnect the adapter from the power source and the device when charging is complete or when the device is not in use.

6. Maintenance

The YUSTDA AC-DC Power Adapter requires minimal maintenance:

  • Cleaning: Disconnect the adapter from all power sources before cleaning. Use a soft, dry cloth to wipe the exterior. Do not use liquid cleaners or solvents.
  • Storage: Store the adapter in a cool, dry place away from direct sunlight and extreme temperatures when not in use. Avoid tightly coiling the cable to prevent damage.
  • Inspection: Periodically inspect the cable and adapter housing for any signs of wear, cuts, or damage. If damage is observed, discontinue use immediately.

7. Troubleshooting

If you encounter issues with your power adapter, refer to the following common solutions:

ProblemPossible CauseSolution
Device not charging/powering on.
  • Adapter not properly plugged in.
  • Power outlet is not active.
  • Device is not compatible.
  • Damaged adapter or cable.
  • Ensure all connections are secure.
  • Test the outlet with another device.
  • Verify your device model against the compatible list in the "Specifications" section.
  • Discontinue use if damaged and replace.
Adapter feels excessively hot.
  • Poor ventilation.
  • Overload.
  • Internal fault.
  • Ensure the adapter is in an open area.
  • Confirm the connected device's power requirements do not exceed 45 watts.
  • Unplug immediately and discontinue use.
Intermittent power supply.
  • Loose connection.
  • Damaged cable.
  • Check all connections.
  • Inspect the cable for damage. Replace if necessary.

If the problem persists after attempting these solutions, contact customer support for further assistance.

8. Specifications

BrandYUSTDA
ModelTNS30W-xy
Input Voltage100-240VAC, 50/60Hz
Wattage45 watts
Cable Length10 feet (approximately 3 meters)
Connector TypeBarrel Connector
Special FeaturesOver current protection, Total power protection, Over voltage protection, Short Circuit Protection
Compatible DevicesYaesu Standard Horizon Radio models: HX890, HX150, HX210, HX300, HX380, HX400, HX400IS, HX407, HX870, HX40, HX270s, HX280s, HX290, HX350s, HX370s, HX460s, HX470s, HX471s, HX500s, HX600s, HX750s, HX751, HX850s, HX851
CertificationsFCC, CE, RoHS

9. Warranty and Support

For warranty information or technical support, please refer to the documentation provided with your purchase or contact YUSTDA customer service directly. Keep your purchase receipt as proof of purchase.

Manufacturer: YUSTDA

© 2023 YUSTDA. All rights reserved.