Mustang 79700 Lowdown Touring One-Piece Seat Instruction Manual

1. Product Overview

The Mustang 79700 Lowdown Touring One-Piece Seat is designed to enhance the riding experience for Harley-Davidson touring models. This seat features a rider's bucket shaped and angled for optimal touring posture. It is also designed to position the rider lower than the stock seat on most models and is cut narrow at the front to facilitate easier ground reach when stopped.

Compatibility: This seat is compatible with Harley-Davidson Road King, Street Glide, Electra Glide, and Road Glide models from 2008-2021, and Street Glide Trike and Tri-Glide models from 2009-2021.

Note: This seat will fit with a handrail. It will not work with H-D or Mustang driver backrest kits.

2. Setup and Installation

This section provides instructions for installing your new Mustang 79700 Lowdown Touring One-Piece Seat.

2.1 Tools Required

• Phillips screwdriver
• Retained stock 1/4"-20 x 1/2" rear fender screw (from your original seat)

2.2 Installation Steps

1. Remove Existing Seat: Locate and remove the rear fender screw securing your current motorcycle seat. Carefully lift and slide the old seat off the motorcycle.
2. Position New Seat: Align the front tongue of the Mustang 79700 seat with the slot on your motorcycle's frame. Ensure the seat is properly seated and flush against the tank.
3. Secure Rear of Seat: Gently press down on the rear of the new seat to align the mounting hole with the fender screw hole. Use the retained stock 1/4"-20 x 1/2" rear fender screw and a Phillips screwdriver to secure the seat firmly in place. Do not overtighten.
4. Verify Installation: Ensure the seat is securely attached and does not move or wobble. Check all contact points for proper fitment.

Image: The Mustang 79700 Lowdown Touring One-Piece Seat. This black, one-piece seat features a contoured design for both rider and passenger, with distinct stitching along the edges. The rider's section is bucket-shaped, and the passenger section is slightly raised.

3. Operating and Usage

The Mustang 79700 seat is engineered for improved comfort and rider positioning during touring. The contoured design supports the rider's posture, reducing fatigue on long rides. The narrower front profile allows for easier ground access, which can enhance confidence and control when stopping or maneuvering at low speeds.

The passenger area is also designed for comfort, providing adequate support for two-up riding.

4. Maintenance

Proper care will extend the life and appearance of your Mustang seat.

4.1 Cleaning

• For routine cleaning, wipe the seat surface with a soft, damp cloth.
• For more stubborn dirt, use a mild soap solution specifically designed for vinyl or leather, depending on your seat's material.
• Avoid harsh chemicals, abrasive cleaners, or stiff brushes, as these can damage the seat material.
• Rinse thoroughly with a clean, damp cloth and dry with a soft, dry cloth.

4.2 Storage

When not in use, store your motorcycle in a covered area to protect the seat from prolonged exposure to direct sunlight and extreme weather conditions, which can cause fading or cracking.

5. Troubleshooting

5.1 Seat Does Not Fit Properly

• Check Compatibility: Verify that your motorcycle model and year fall within the compatible range (Harley-Davidson Touring models 2008-2021).
• Re-align: Ensure the front tongue of the seat is correctly inserted into the frame slot and the rear mounting hole is aligned with the fender screw.
• Obstructions: Check for any obstructions or cables preventing the seat from sitting flush.

5.2 Seat Height Not as Expected

While the Lowdown Touring seat is designed to lower the rider from the stock position on most models, the actual reduction in height can vary depending on the specific motorcycle model and original seat configuration. Some riders may experience a minimal change in seat height.

5.3 Incompatibility with Backrests

As noted in the product overview, this seat is not designed to work with H-D or Mustang driver backrest kits. Attempting to install such accessories may result in improper fitment or damage.

6. Specifications

7. Warranty and Support

For information regarding product warranty, returns, or technical support, please refer to the official Mustang Seats website or contact their customer service directly. Keep your purchase receipt for warranty claims.

Manufacturer: Mustang