1. Introduction
The ANYCUBIC Wash and Cure 3.0 is an upgraded 2-in-1 wash and cure station designed for resin 3D printer models. It features a larger cleaning capacity, innovative gooseneck lights for uniform curing, a dual-layer design for IPA saving, and quiet, simple operation. This manual provides detailed instructions for setup, operation, and maintenance to ensure optimal performance and longevity of your device.
2. Safety Instructions
- Always wear protective gloves and eye protection when handling resin or cleaning solutions.
- Ensure adequate ventilation in your workspace to avoid inhaling resin fumes.
- Keep the device away from children and pets.
- Do not expose the device to direct sunlight or high temperatures.
- Use only recommended cleaning solutions (e.g., Isopropyl Alcohol - IPA) and follow their safety guidelines.
- Never operate the curing function without the UV-blocking top cover in place.
- Disconnect power before cleaning or performing maintenance.
3. What's in the Box
Upon unboxing your ANYCUBIC Wash and Cure 3.0, please verify that all components are present:
- Wash and Cure Machine Unit
- Washing Bucket (4L capacity)
- Washing Basket
- Rack Bar (4 pcs)
- Curing Table
- Gooseneck Light
- Hex Key Set
- User Manual
- Power Adapter
Figure 3.1: All components included in the ANYCUBIC Wash and Cure 3.0 package.
4. Setup Guide
- Unpack: Carefully remove all components from the packaging.
- Placement: Place the main unit on a stable, level surface in a well-ventilated area.
- Power Connection: Connect the power adapter to the unit and then to a power outlet.
- Gooseneck Light Installation: Insert the gooseneck light into its designated port on the main unit.
- Washing Bucket Preparation:
- For washing, place the washing basket inside the washing bucket.
- Fill the washing bucket with your chosen cleaning solution (e.g., IPA) up to the appropriate level, ensuring it covers the models to be cleaned.
- Curing Table Preparation: For curing, ensure the curing table is placed on the rotating platform.
Video 4.1: Official overview of the Wash and Cure 3.0, demonstrating its features and basic setup.
5. Operating Instructions
5.1. Washing Mode
- Prepare Models: Remove printed models from the build plate. For models still on the build plate, use the hanging cleaning mode. For detached models, place them in the washing basket.
- Place Washing Bucket: Position the washing bucket with the models and cleaning solution onto the main unit's platform. Ensure the UV-blocking cover is in place.
- Select Wash Mode: Press the "Wash" button on the control panel.
- Set Time: Use the rotary knob to set the desired washing time (typically 1-30 minutes, refer to resin manufacturer guidelines).
- Start Washing: Press the Start/Stop button to begin the washing cycle. The internal propeller will agitate the cleaning solution.
- Completion: The machine will beep when the cycle is complete. Carefully remove the models and allow them to dry.
Figure 5.1: Dual cleaning modes for models on a build plate (hanging) or detached (basket).
Video 5.1: Demonstration of the washing process in the ANYCUBIC Wash and Cure 2.0 machine, which shares similar washing mechanisms with the 3.0 model.
5.2. Curing Mode
- Place Models: After washing and drying, place the models on the curing table.
- Position Curing Table: Place the curing table with models onto the main unit's rotating platform. Ensure the UV-blocking cover is in place.
- Select Cure Mode: Press the "Cure" button on the control panel.
- Set Time: Use the rotary knob to set the desired curing time (typically 1-30 minutes, refer to resin manufacturer guidelines).
- Activate Gooseneck Light (Optional): Press the "FlexiCure" button to activate the gooseneck light for targeted curing of complex areas.
- Start Curing: Press the Start/Stop button to begin the curing cycle. The platform will rotate, and UV lights will activate.
- Completion: The machine will beep when the cycle is complete. Remove the fully cured models.
Figure 5.2: The gooseneck light provides localized strengthening and uniform curing for intricate details on 3D models.
Video 5.2: A user demonstrating the curing process with the ANYCUBIC Wash and Cure station, highlighting its ease of use.
6. Maintenance
- Cleaning the Washing Bucket: Regularly clean the washing bucket and basket to prevent resin buildup. Dispose of used cleaning solution responsibly according to local regulations.
- Cleaning the Unit: Wipe down the exterior of the unit with a soft, dry cloth. Avoid using abrasive cleaners or solvents.
- UV Light Maintenance: Keep the UV lights and gooseneck light clean and free of dust or resin residue to ensure optimal curing performance.
- Storage: When not in use, store the unit in a cool, dry place away from direct sunlight.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Device does not power on. | Power cable not connected; power outlet issue. | Check power cable connection; try a different outlet. |
| Washing/Curing cycle does not start. | Top cover not properly closed; mode not selected. | Ensure the UV-blocking cover is securely in place; select desired mode (Wash/Cure). |
| Models are not clean after washing. | Insufficient washing time; dirty cleaning solution; incorrect IPA concentration. | Increase washing time; replace cleaning solution; ensure proper IPA concentration. |
| Models are sticky after curing. | Insufficient curing time; models not dry before curing; UV lights are dirty. | Increase curing time; ensure models are completely dry; clean UV lights. |
8. Specifications
| Feature | Detail |
|---|---|
| Model | Wash and Cure 3 |
| Product Dimensions | 8.86 x 8.66 x 14.88 inches |
| Item Weight | 0.01 ounces |
| Brand | ANYCUBIC |
| Material | PC+metal |
| Color | Multi-color |
| Maximum Cleaning Volume | 165 x 100 x 180 mm (4L bucket) |
| UV Light | 10pcs 405nm + Gooseneck Light |
| Maximum Curing Size | Φ160 x 180 mm |
| Timer | 1-30 minutes adjustable |
Figure 8.1: Detailed comparison of Wash and Cure 3 and Wash and Cure 3 Plus specifications.
9. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the official ANYCUBIC website or contact their customer service directly. Keep your purchase receipt as proof of purchase for warranty claims.
You can visit the ANYCUBIC Official Store for more products and support resources.
