GE 25 LED C-9 Warm White String Lights Instruction Manual

Introduction

Thank you for choosing GE 25 LED C-9 Warm White String Lights. This product is designed for both indoor and outdoor decorative lighting. These energy-efficient LED lights provide a warm white glow, perfect for various seasonal and general lighting needs. This manual provides important information regarding the safe installation, operation, and maintenance of your new light set.

Key Features:

• 25-count warm white diamond cut StayBright LED lights.
• 12-feet lighted length with a green cord and fused plug.
• Connectable: Up to 25 sets can be connected end-to-end.
• Suitable for indoor and outdoor use.
• Includes replacement bulbs and fuses.

Important Safety Instructions

When using electrical products, basic precautions should always be followed, including the following:

1. Read all instructions before using this product.
2. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
3. This seasonal product is not intended for permanent installation or use.
4. Do not mount or place near gas or electric heaters, fireplaces, candles, or other similar sources of heat.
5. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
6. Do not let lamps rest on the supply cord or on any wire.
7. Unplug the product when leaving the house, when retiring for the night, or if left unattended.
8. This is an electrical product, not a toy! To avoid risk of fire, burns, personal injury, and electric shock, it should not be played with or placed where small children can reach it.
9. Do not use this product for other than its intended use.
10. Do not hang ornaments or other objects from cord, wire, or light string.
11. Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
12. Do not cover the product with cloth, paper, or any material not part of the product when in use.
13. This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit condition. If the fuse blows, unplug the product from the outlet. Also unplug any additional strings or products that may be attached to the product. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit condition may be present and the product should be discarded.
14. Read and follow all instructions that are on the product or provided with the product.

SAVE THESE INSTRUCTIONS

Setup and Installation

Follow these steps for proper setup and installation of your GE LED C-9 lights:

1. Unpack the Lights: Carefully remove the light set from its packaging. Untangle the cord and ensure all bulbs are securely seated in their sockets.
2. Inspect the Set: Before plugging in, inspect the light set for any damage to the cord, bulbs, or plug. Do not use if any damage is found.
3. Placement: These lights are suitable for both indoor and outdoor use. For outdoor applications, ensure the connection to a GFCI outlet.
4. Connecting Multiple Sets: You can connect up to 25 sets of these GE LED C-9 lights end-to-end. To do this, simply plug the end connector of one set into the fused plug of the next set. Ensure the total wattage of connected sets does not exceed the maximum recommended load (refer to specifications).
5. Securing the Lights: Use appropriate clips or ties to secure the lights. Avoid using staples, nails, or sharp objects that could damage the wiring. Ensure the bulbs are not resting directly on the cord.

Image: A section of the GE 25 LED C-9 Warm White String Lights, showing the individual C-9 shaped LED bulbs spaced along the green wire.

Image: Close-up of the green fused plug for the GE LED C-9 light set, showing the 125V FUSE and 3A MAX markings.

Operating Instructions

Operating your GE LED C-9 lights is straightforward:

1. Once the lights are properly installed and secured, plug the fused plug into a suitable electrical outlet.
2. The lights will illuminate immediately.
3. To turn off, simply unplug the light set from the outlet.
4. For outdoor use, ensure the outlet is weather-protected and ideally a GFCI outlet.

Maintenance

Proper maintenance ensures the longevity and safe operation of your light set.

Replacing Fuses

This product employs overload protection (fuse). If the entire string does not light up, the fuse may be blown. To replace the fuse:

1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
2. Open fuse cover. Slide open the fuse access cover on top of the attachment plug towards the blades.
3. Carefully remove old fuse.
4. Replace fuse with only 3 Amp, 125 Volt fuse (provided).
5. Close fuse cover. Slide closed the fuse access cover on top of the attachment plug.

Caution: Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged.

Replacing Bulbs

If individual bulbs go out, they can be replaced. The set includes replacement LED bulbs.

1. Unplug the light set from the power source.
2. Gently twist the non-working bulb counter-clockwise and pull it straight out from its socket.
3. Insert a new replacement LED bulb into the socket, aligning the base correctly, and twist clockwise until secure.
4. Ensure all bulbs are securely seated before plugging the set back in.

Note: The product includes 10 replacement LED bulbs.

Troubleshooting

If your GE LED C-9 lights are not functioning as expected, refer to the following common issues and solutions:

• Lights do not turn on:
  • Ensure the plug is fully inserted into a working electrical outlet.
  • Check the fuse in the plug and replace if blown (refer to "Replacing Fuses" section).
  • If connecting multiple sets, ensure the total number of sets does not exceed 25.
  • Verify that the outlet is receiving power (test with another device).
• Some bulbs are out:
  • Individual LED bulbs can be replaced. Refer to the "Replacing Bulbs" section.
  • Ensure all bulbs are securely twisted into their sockets.
• Fuses blow repeatedly:
  • This indicates an overload or short circuit. Disconnect all connected sets and inspect for damaged wires or bulbs.
  • Do not connect more than 25 sets end-to-end.
  • If the issue persists after replacing the fuse and checking for damage, the product may have an internal fault and should be discarded.

Specifications

Image: A close-up of the product packaging showing detailed specifications for the GE 25 LED C-9 Lights, including LED count, wattage, spacing, and connectability.

Warranty and Support

GE products are manufactured to high-quality standards. For specific warranty information, please refer to the product packaging or contact GE customer support. In case of issues or questions not covered in this manual, please reach out to the manufacturer's customer service for assistance.

Manufacturer: GE

Model Number: 90976LO

UPC: 803993909769