Husky 5000-Lumen Portable LED Work Light Instruction Manual

Introduction

This manual provides essential information for the safe and efficient operation of your Birsppy Husky 5000-Lumen Portable LED Work Light. Please read this manual thoroughly before use and retain it for future reference. This work light is designed to provide ample illumination for various tasks, featuring a durable LED bulb and a versatile design that allows for use with or without its tripod stand.

Safety Information

Always observe the following safety precautions to reduce the risk of injury or damage:

• Ensure the work light is placed on a stable, level surface to prevent tipping.
• Do not look directly into the LED light source when it is illuminated, as this may cause eye strain or damage.
• Keep the work light away from flammable materials.
• Do not operate the light in wet locations or expose it to rain. The caution label on the back of the unit states: "KEEP THE COVER CLOSED. DO NOT OPEN THE COVER IN WET LOCATIONS."
• Always unplug the unit from the power source before cleaning or performing any maintenance.
• Do not attempt to modify or repair the unit yourself. Contact qualified service personnel for assistance.
• Use only the specified power source (5 Volts DC, 120V AC 10A).

Figure 1: Rear view of the work light, highlighting the caution label regarding wet conditions and keeping the cover closed. This label is located near the power input ports.

Package Contents

Verify that all items are present upon unpacking:

• Husky 5000-Lumen LED Work Light Unit
• Adjustable Stand/Tripod Base
• Power Cord (integrated or separate, typically integrated for work lights)
• Instruction Manual (this document)

Product Overview

The Husky 5000-Lumen Portable LED Work Light features a robust design for various applications. Key components include:

• LED Light Panel: High-brightness, long-lasting LED for powerful illumination.
• Adjustable Stand: Allows for stable placement and angle adjustment.
• Easy-Grip Handle: For convenient portability when detached from the stand.
• Power Input/Output Ports: Includes AC outlet and USB port for additional utility.

Figure 2: Front view of the work light, showcasing the LED panel and the adjustable stand with red knobs.

Figure 3: Rear view of the work light, detailing the integrated AC power outlet and USB charging port, protected by a clear cover.

Figure 4: A detailed close-up of the power input/output section, showing the 5V DC USB port and the 120V AC 10A outlet, both covered for protection.

Setup

1. Unpacking: Carefully remove all components from the packaging. Inspect for any damage.
2. Attaching the Stand (if separate): If the stand is not pre-attached, align the work light unit with the stand's mounting point and secure it using the provided knob or screw. Ensure it is tightened firmly.
3. Positioning: Place the work light on a stable, flat surface. Adjust the angle of the light panel using the red adjustment knobs on the sides of the stand. Loosen the knobs, set the desired angle, and then tighten them to secure the position.
4. Power Connection: Plug the power cord into a standard 120V AC electrical outlet. Ensure the outlet is properly grounded.

Figure 5: Side view illustrating the adjustable head of the work light, showing its range of motion for directing illumination.

Operating Instructions

1. Turning On/Off: Locate the power switch, typically on the back or side of the unit. Press it to turn the light on or off.
2. Adjusting Light Angle: Loosen the red adjustment knobs on the sides of the stand, tilt the light panel to the desired angle, and then firmly tighten the knobs to secure it.
3. Using the Integrated Outlets:
   • AC Outlet: Lift the protective cover and plug in compatible 120V AC tools or devices. Do not exceed the specified amperage (10A).
   • USB Port: Lift the protective cover and connect a USB cable to charge compatible 5V DC devices.

   Important: Always ensure the protective covers for the outlets are closed when not in use, especially in dusty or damp environments, to prevent damage and ensure safety.
4. Portable Use: The light unit can be detached from its stand for handheld or temporary placement. Use the integrated handle for easy transport.

Maintenance

• Cleaning: Disconnect the power before cleaning. Wipe the exterior surfaces with a soft, damp cloth. Do not use abrasive cleaners or solvents.
• Storage: Store the work light in a dry, cool place when not in use.
• LED Bulb: The LED bulb is designed for long life and typically does not require replacement. Do not attempt to open the sealed light panel.

Troubleshooting

If troubleshooting steps do not resolve the issue, contact customer support for further assistance.

Specifications

Warranty and Support

For warranty information or technical support, please refer to the contact details provided with your purchase documentation or visit the official Birsppy website. Keep your proof of purchase for warranty claims.