LUX-TOOLS SLG-20/2x2.4 Double Fast Charger Instruction Manual

1. Introduction

This instruction manual provides essential information for the safe and effective operation, setup, and maintenance of your LUX-TOOLS SLG-20/2x2.4 Double Fast Charger. This charger is specifically designed for use with LUX-TOOLS 1PowerSystem 20V lithium-ion batteries. Please read this manual thoroughly before first use and retain it for future reference.

2. Safety Instructions

Always observe the following safety precautions to prevent electric shock, fire, or serious injury:

• Read all instructions: Before using the charger, read all instructions and cautionary markings on the charger, battery, and product using the battery.
• Indoor use only: Do not expose the charger to rain or wet conditions.
• Proper voltage: Ensure the power supply voltage matches the voltage specified on the charger's rating plate.
• Avoid charging damaged batteries: Do not attempt to charge batteries that are visibly damaged or defective.
• Use only specified batteries: This charger is designed exclusively for LUX-TOOLS 1PowerSystem 20V lithium-ion batteries. Charging other types of batteries may cause personal injury and damage.
• Ventilation: Ensure adequate ventilation during charging. Do not cover the charger.
• Unplug when not in use: Disconnect the charger from the power outlet when not in use or before cleaning.
• Children and unauthorized persons: This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

3. Product Overview

The LUX-TOOLS SLG-20/2x2.4 is a dual-port fast charger designed to efficiently charge two LUX-TOOLS 1PowerSystem 20V batteries simultaneously. It features LED indicators to display the charging status of each battery.

Image 1: Overview of the LUX-TOOLS SLG-20/2x2.4 Double Fast Charger. The charger is gray and green with two battery slots and an LED indicator panel.

Image 2: Close-up of the charger's front panel, showing the LED indicators for each charging slot. These LEDs provide visual feedback on the charging status.

LED Indicator Status:

• Red LED (Solid): Charging in progress.
• Green LED (Solid): Battery fully charged.
• Red LED (Flashing): Battery error or temperature issue. Remove battery and allow it to cool, then reinsert. If the error persists, the battery may be defective.

4. Setup

1. Unpack: Carefully remove the charger from its packaging. Inspect for any signs of damage.
2. Placement: Place the charger on a stable, flat, non-flammable surface in a well-ventilated area. Ensure it is away from direct sunlight, heat sources, and moisture.
3. Connect Power: Plug the charger's power cord into a suitable electrical outlet. The charger is now ready for use.

5. Operating Instructions

Charging a Battery:

1. Insert Battery: Align the LUX-TOOLS 1PowerSystem 20V battery with one of the charging slots on the charger. Slide the battery firmly into the slot until it clicks into place. You can insert a second battery into the other slot if needed.

Image 3: A hand demonstrating the correct way to insert a LUX-TOOLS 1PowerSystem 20V battery into one of the charger's slots.
2. Monitor Charging: The corresponding red LED indicator for the inserted battery will illuminate, indicating that charging has begun.
3. Charging Time: The charger provides a fast charge rate of 2.4 A. A 2 Ah battery typically charges in approximately one hour, while a 4 Ah battery charges in about two hours.
4. Charging Complete: Once the battery is fully charged, the red LED will turn off, and the green LED will illuminate.
5. Remove Battery: To remove the battery, press the release button on the battery pack and slide it out of the charger slot.

Compatibility:

This charger is an integral part of the LUX-TOOLS 1PowerSystem and is compatible with all batteries within this series. The 1PowerSystem offers a wide range of tools that utilize the same 20V battery platform.

Image 4: An illustration showcasing the extensive range of tools within the LUX-TOOLS 1PowerSystem, all powered by the same 20V battery platform.

6. Maintenance

• Cleaning: Disconnect the charger from the power supply before cleaning. Use a dry, soft cloth to wipe the exterior of the charger. Do not use abrasive cleaners or solvents.
• Storage: Store the charger in a dry, cool place, away from direct sunlight and moisture, when not in use.
• Inspection: Regularly inspect the charger and its power cord for any signs of damage. If damage is found, do not use the charger and contact customer support.

7. Troubleshooting

• Charger not working: Ensure the charger is securely plugged into a working power outlet. Check for any visible damage to the power cord or charger.
• Battery not charging (Red LED flashing): This indicates a battery error or temperature issue. Remove the battery from the charger and allow it to cool down if it feels warm. Reinsert the battery. If the error persists, the battery may be defective and require replacement.
• Slow charging: Ensure the charger is operating within its specified temperature range. Extreme temperatures can affect charging performance.

8. Specifications

9. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the warranty card included with your product or contact LUX-TOOLS customer service directly. Keep your purchase receipt as proof of purchase.