Lamicall LS07-MX-B
Lamicall Gooseneck Tablet Mount Holder User Manual
Model: LS07-MX-B
Introduction
Thank you for choosing the Lamicall Gooseneck Tablet Mount Holder. This flexible and versatile mount is designed to provide a comfortable and ergonomic viewing experience for your tablet or smartphone in various settings, including your bed, desk, or sofa. Please read this manual carefully before use to ensure proper installation and operation.
Figure 1: Lamicall Gooseneck Tablet Mount Holder
Safety Information
Please observe the following safety precautions to prevent damage to the product or injury to yourself:
- Do not overtighten the clamp on surfaces, as this may cause damage to furniture.
- Ensure the mount is securely fastened before attaching your device.
- Avoid bending the gooseneck arm excessively or repeatedly at the same point, as this can weaken the internal structure over time.
- When adjusting the gooseneck, use both hands: one to stabilize the base and the other to bend the arm.
- Do not use the mount for supporting devices heavier than recommended.
- Keep out of reach of small children.
Package Contents
Verify that all components are present in your package:
- 1 x Lamicall Gooseneck Tablet Mount Holder (Flexible Arm with Clamp Base)
- 1 x Device Holder (Tablet/Phone Clamp)
Setup Instructions
Follow these steps to set up your Lamicall Gooseneck Tablet Mount Holder:
- Attach the Clamp Base: Identify a suitable surface (e.g., desk, bedside table, headboard) with a thickness between 0 and 2.7 inches (0-70mm). Unscrew the clamp knob to open the clamp jaws. Position the clamp onto the edge of the surface and tighten the knob securely until the clamp is firm and stable.
Figure 2: Secure Clamp Base
- Insert the Device Holder: The device holder (tablet/phone clamp) typically comes pre-attached to the gooseneck arm. If not, ensure it is firmly screwed onto the ball joint at the end of the gooseneck arm.
- Mount Your Device: Gently pull apart the spring-loaded grips of the device holder. Carefully insert your tablet or smartphone (compatible with 4.7-11 inch devices) into the holder, ensuring it is centered and held firmly by the protective rubber grips.
Figure 3: Device Holder Grips
Operating Instructions
Using your Lamicall Gooseneck Tablet Mount Holder for optimal viewing:
- Adjusting the Gooseneck Arm: The flexible arm has an overall length of 36 inches (920mm). To adjust the viewing angle and distance, use both hands to carefully bend the gooseneck arm. For better stability, especially with heavier devices, bend the gooseneck into an "S" or "Z" shape to create multiple support points.
Figure 4: Flexible Arm in Office Use
- Rotating Your Device: The device holder features 360-degree rotation. You can easily switch between portrait and landscape orientations by gently rotating your device within the holder.
Figure 5: Optimal Viewing in Bed
- Ergonomic Positioning: Position your device at a comfortable distance from your eyes to reduce strain and maintain an ergonomic posture, especially during extended viewing sessions.
Figure 6: Relaxed Viewing Posture
Note: This mount is primarily designed for viewing content. It is not recommended for heavy typing or touch interactions that may cause the arm to wobble slightly.
Maintenance
To ensure the longevity of your Lamicall Gooseneck Tablet Mount Holder:
- Clean the mount with a soft, dry cloth. Avoid abrasive cleaners or solvents.
- Periodically check the tightness of the clamp and the device holder to ensure they remain secure.
- Store the mount in a cool, dry place when not in use.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Mount wobbles or sags. | Clamp not tight enough; arm not properly shaped; device too heavy. | Ensure clamp is fully tightened. Bend the gooseneck into an "S" or "Z" shape for added stability. Verify device weight is within limits. |
| Device slips from holder. | Device not centered; holder not fully gripping. | Re-position device to be centered within the grips. Ensure the spring-loaded grips fully enclose the device. |
| Gooseneck arm is difficult to bend. | Arm is designed to be stiff for stability. | Use both hands to adjust the arm, one hand stabilizing the base and the other bending the arm. Avoid bending at sharp angles. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | LS07-MX-B |
| Brand | Lamicall |
| Color | Black |
| Compatible Device Size | 4.7 - 11 inches (Tablets and Cellphones) |
| Gooseneck Length | Approx. 36 inches (920mm) |
| Clamp Opening Range | 0 - 2.7 inches (0-70mm) |
| Rotation | 360-degree (Device Holder) |
| Material | High quality magnalium alloy (gooseneck), durable plastic (clamp/holder) |
Figure 7: Product Dimensions
Warranty and Support
Lamicall products come with a standard warranty. For specific warranty terms and conditions, please refer to the warranty card included with your purchase or visit the official Lamicall website.
If you encounter any issues or have questions regarding your Lamicall Gooseneck Tablet Mount Holder, please contact Lamicall Customer Support:
- Website: www.lamicall.com
- Email: Refer to website for contact details.
Please have your model number (LS07-MX-B) and purchase information ready when contacting support.
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.