Product Overview
This manual provides essential information for the installation, operation, and maintenance of your Elettrobar Pre-wash Table, Model 80206L. This stainless steel pre-wash table is designed for commercial use with hood-type dishwashers, specifically accommodating basket sizes of 500 x 500 mm or 600 x 500 mm. The unit features a right-hand attachment point for seamless integration with your dishwasher setup.
Dimensions: 700 mm (Length) x 715 mm (Width) x 850 mm (Height).
Figure 1: Elettrobar Pre-wash Table (Model 80206L). This image shows the overall design of the stainless steel pre-wash table, featuring a built-in sink and a lower shelf for storage. The right-hand attachment point for a dishwasher is visible.
Setup and Installation
Proper setup is crucial for the stability and functionality of the pre-wash table. Follow these steps carefully:
- Unpacking: Carefully remove all packaging materials. Inspect the table for any signs of damage incurred during transit. Report any damage to your supplier immediately.
- Placement: Position the pre-wash table on a flat, stable surface in your commercial kitchen. Ensure adequate space around the unit for operation and maintenance. The right-hand attachment is designed to connect to the left side of your hood dishwasher.
- Leveling: The table is equipped with adjustable feet. Use a spirit level to ensure the table is perfectly level. Adjust each foot as necessary to eliminate any wobbling and ensure proper drainage from the sink.
- Drain Connection: Connect the sink's drain outlet to your facility's wastewater system. Ensure all connections are secure and watertight to prevent leaks.
- Water Supply (if applicable): If the sink includes a faucet (not supplied with the table), connect it to a potable water supply according to local plumbing codes.
Figure 2: Schematic Diagram. This diagram illustrates the basic structure and dimensions of the pre-wash table, including the sink and lower shelf, providing a visual guide for installation planning.
Configuration Examples
The Elettrobar Pre-wash Table can be configured with various hood dishwashers. Below are examples for different basket sizes:
For 600 x 500 mm Baskets
Figure 3: Example setup for dishwashers using 600 x 500 mm baskets. This image shows the pre-wash table integrated with a hood dishwasher, demonstrating the typical workflow for larger basket sizes.
For 500 x 500 mm Baskets
Figure 4: Example setup for dishwashers using 500 x 500 mm baskets. This image illustrates the pre-wash table's compatibility and integration with standard commercial dishwashers.
Operating Instructions
The pre-wash table is designed to facilitate the efficient pre-treatment of dishes before they enter the dishwasher. Follow these general operating guidelines:
- Scraping: Before placing dishes in the sink, scrape off any large food particles into a waste bin. This prevents clogging of the drain and reduces the load on the dishwasher.
- Pre-rinsing: Use the sink to pre-rinse dishes with water, removing remaining food debris. This step significantly improves dishwasher performance and hygiene.
- Loading Baskets: Load the pre-rinsed dishes into appropriate dishwasher baskets (500x500mm or 600x500mm) on the table surface. Ensure dishes are spaced correctly for effective washing.
- Transfer to Dishwasher: Slide the loaded baskets directly into the hood dishwasher from the pre-wash table's right-hand attachment side.
Care and Maintenance
Regular cleaning and maintenance will extend the life of your Elettrobar Pre-wash Table and ensure optimal hygiene.
- Daily Cleaning: After each use, or at the end of the day, thoroughly clean all stainless steel surfaces with a mild detergent and warm water. Rinse with clean water and dry with a soft cloth to prevent water spots and streaks.
- Sink and Drain: Regularly clean the sink basin and ensure the drain is free of food particles and debris. Use a drain cleaner specifically designed for commercial kitchen use if blockages occur.
- Stainless Steel Care: Avoid using abrasive cleaners, steel wool, or harsh chemicals (e.g., bleach, strong acids) on the stainless steel, as these can scratch or corrode the surface. For stubborn stains, use a stainless steel cleaner and polish, always rubbing in the direction of the grain.
- Inspection: Periodically inspect the table for any loose connections, damaged components, or signs of wear. Address any issues promptly to prevent further damage.
Troubleshooting
This section addresses common issues you might encounter with your pre-wash table.
| Problem | Possible Cause | Solution |
|---|---|---|
| Water not draining from sink | Clogged drain or trap | Remove drain cover and clear any visible debris. If blockage persists, use a drain snake or commercial drain cleaner. |
| Table is wobbly or unstable | Uneven floor or unadjusted feet | Adjust the leveling feet until the table is stable and level. Ensure all feet are firmly on the ground. |
| Water leaks from drain connection | Loose connection or damaged seal | Check all drain connections for tightness. Replace any worn or damaged gaskets/seals. |
| Stainless steel surface shows stains/discoloration | Hard water spots, improper cleaning agents, or food residue | Clean with a stainless steel cleaner and polish. Avoid abrasive materials and chlorine-based cleaners. Dry thoroughly after cleaning. |
Product Specifications
| Feature | Detail |
|---|---|
| Brand | Elettrobar |
| Model Number | 80206L |
| Material | Stainless Steel |
| Dimensions (L x W x H) | 700 mm x 715 mm x 850 mm |
| Compatibility | Hood dishwashers with 500x500 mm or 600x500 mm baskets |
| Attachment Side | Right-hand (for connection to the left side of a dishwasher) |
| UPC | 645760605579 |
Warranty Information
Specific warranty details for the Elettrobar Pre-wash Table (Model 80206L) are not provided in this manual. For information regarding warranty coverage, terms, and conditions, please refer to the documentation supplied with your purchase or contact your authorized Elettrobar dealer or the manufacturer directly.
Customer Support
For technical assistance, spare parts, or any inquiries not covered in this manual, please contact your supplier or the official Elettrobar customer support. When contacting support, please have your product model number (80206L) and purchase details readily available.
You may find contact information on the manufacturer's official website or through your point of purchase.
