BRILHO ENVISION Chain Lube and Cleaner Combo User Manual

1. Product Overview

The BRILHO ENVISION Chain Lube and Cleaner Combo is designed for comprehensive maintenance of motorcycle, moped, and other chain-driven vehicle chains. This combo includes a high-quality chain cleaner and a powerful chain lubricant, formulated to ensure optimal performance and longevity of your vehicle's chain system.

The chain cleaner effectively removes encrusted deposits such as sand, dirt, oil, and grease, while the chain lube provides superior lubrication with heavy-duty, anti-wear, and extreme pressure additives.

Image 1.1: The BRILHO ENVISION Chain Lube and Cleaner Combo, showing two aerosol cans: one for chain cleaning and one for chain lubrication.

2. Safety Information

• Use in a well-ventilated area.
• Keep out of reach of children and pets.
• Avoid contact with eyes and skin. In case of contact, rinse thoroughly with water.
• Do not ingest. If swallowed, seek immediate medical attention.
• Flammable: Keep away from heat, sparks, open flames, and hot surfaces. No smoking.
• Pressurized container: Do not pierce or burn, even after use.
• Store in a cool, dry place, away from direct sunlight.
• Always wear appropriate personal protective equipment, such as gloves and eye protection, when handling these products.

3. Preparation and Setup

Before applying the chain cleaner and lube, ensure your vehicle is stable and secure. It is recommended to use a paddock stand or center stand to lift the rear wheel, allowing for free rotation of the chain.

1. Park the vehicle on a flat, stable surface.
2. Engage the parking brake if applicable.
3. Place the vehicle on a paddock stand or center stand to elevate the rear wheel.
4. Ensure the engine is off and cool.
5. Gather necessary tools: BRILHO ENVISION Chain Cleaner, BRILHO ENVISION Chain Lube, a chain cleaning brush (optional), and a clean cloth.
6. Wear protective gloves and eye protection.

4. Operating Instructions

4.1. Chain Cleaning Procedure

Use the BRILHO ENVISION Chain Cleaner to remove dirt, grime, and old lubricant from the chain.

1. Shake the BRILHO ENVISION Chain Cleaner can well before use.
2. Hold the can approximately 10-15 cm (4-6 inches) from the chain.
3. Spray the cleaner evenly along the entire length of the chain while slowly rotating the rear wheel. Ensure all sides of the chain links are covered.
4. Allow the cleaner to penetrate and dissolve dirt for a few minutes (refer to product label for specific timing).
5. For heavily soiled chains, use a chain cleaning brush to agitate and loosen stubborn deposits.
6. Wipe off excess cleaner and dissolved grime with a clean, dry cloth. Ensure the chain is thoroughly dry before applying lubricant.

4.2. Chain Lubrication Procedure

After cleaning, apply the BRILHO ENVISION Chain Lube to protect and lubricate the chain.

1. Ensure the chain is completely clean and dry from the previous cleaning step.
2. Shake the BRILHO ENVISION Chain Lube can well before use.
3. Hold the can approximately 5-10 cm (2-4 inches) from the chain.
4. Apply a thin, even coat of lubricant to the inner side of the chain, focusing on the rollers and pins, while slowly rotating the rear wheel.
5. Ensure the lubricant penetrates all moving parts of the chain. Avoid over-applying, as excess lube can attract dirt.
6. Allow the lubricant to set for at least 10-15 minutes, or as recommended on the product label, before riding. This allows the solvent to evaporate and the lubricant to thicken.
7. Wipe off any excess lubricant from the outer plates of the chain and surrounding areas with a clean cloth to prevent fling-off.

5. Maintenance Tips

• Regularly inspect your chain for signs of wear, rust, or excessive dirt buildup.
• Clean and lubricate your chain every 500-1000 km (300-600 miles) or more frequently if riding in wet, dusty, or off-road conditions.
• Always clean the chain thoroughly before applying new lubricant to prevent abrasive particles from being trapped.
• Store the BRILHO ENVISION products in a cool, dry place, away from direct sunlight and extreme temperatures.

6. Troubleshooting

While the BRILHO ENVISION Chain Lube and Cleaner Combo is designed for straightforward use, here are some common issues and their solutions:

7. Specifications

8. Contact and Support

For further assistance, questions, or support regarding your BRILHO ENVISION Chain Lube and Cleaner Combo, please refer to the contact information provided on the product packaging or visit the official BRILHO ENVISION website.

Note: Specific warranty details are typically provided with the product packaging or on the manufacturer's official website.