Crivit Sports Bicycle Helmet User Manual

1. Introduction

The Crivit Sports Bicycle Helmet is designed for both him and her, offering a blend of safety, comfort, and lightweight design. Constructed with modern in-mould technology, it features an impact-resistant polycarbonate outer shell and a highly absorbent EPS inner shell for enhanced stability and heat resistance. This helmet is equipped with features aimed at providing an optimal fit, excellent ventilation, and improved visibility for cyclists.

2. Key Features

• Extremely Lightweight: Weighing approximately 300g, designed for comfort during long rides.
• High Stability & Heat Resistance: Achieved through modern in-mould construction.
• Durable Construction: Outer shell made of impact-resistant polycarbonate and inner shell of highly absorbent EPS.
• Optimal Fit System: Patented one-hand size adjustment system with a continuous rotary switch for easy customization.
• Integrated Rear Light: Removable rear light with 6 powerful LEDs offering 3 light levels (steady on, flashing mode, running light) for improved visibility.
• Excellent Ventilation: 11 air channels ensure optimal air circulation and a comfortable head climate.
• Comfort & Hygiene: Features a chin pad for high wearing comfort and a removable, washable inner lining for hygiene.
• Enhanced Visibility: Reflective elements integrated into the design.
• Additional Protection: Includes insect protection and a removable visor.

3. Setup and Adjustment

Figure 3.1: The Crivit Sports Bicycle Helmet, illustrating its lightweight design, integrated visor, and adjustable chin strap.

1. Initial Fit Adjustment: Place the helmet on your head. It should sit level and cover your forehead.
2. Size Adjustment System: Locate the patented one-hand size adjustment system at the back of the helmet. Use the continuous rotary switch to tighten or loosen the internal retention system until the helmet fits snugly and comfortably without being too tight or causing pressure points. The helmet should not move significantly when you shake your head.
3. Strap Adjustment: Adjust the side straps so that they form a "V" shape just below your ears. The strap dividers should sit flat against your skin.
4. Chin Strap Buckle: Fasten the chin strap buckle. Adjust the strap length so that it is snug under your chin, allowing only one or two fingers to fit between the strap and your chin. Ensure the chin pad is positioned for maximum comfort.
5. Visor Attachment: The helmet comes with a removable visor. Attach it securely to the designated slots at the front of the helmet if desired.
6. Insect Protection: The integrated insect protection helps prevent insects from entering the helmet's air channels.

4. Operating Instructions

4.1 Rear Light Operation

The Crivit Sports Bicycle Helmet is equipped with a removable rear light for enhanced visibility, especially in low-light conditions. The light features 6 powerful LEDs and offers three distinct light levels:

• Steady On: Provides a continuous beam of light.
• Flashing Mode: The LEDs flash intermittently, drawing attention.
• Running Light: A sequential light pattern for dynamic visibility.

To operate the rear light:

1. Activation: Locate the power button on the rear light unit. Press the button once to turn the light on, typically activating the first mode (e.g., Steady On).
2. Mode Selection: Press the button repeatedly to cycle through the available light modes (Steady On, Flashing Mode, Running Light).
3. Deactivation: Continue pressing the button until the light turns off, or press and hold the button for a few seconds (refer to specific product instructions if available on the device itself for exact hold time).
4. Battery Replacement: The rear light is battery-operated. If the light dims or stops working, replace the batteries as per the instructions provided with the light unit.

5. Maintenance

5.1 Cleaning

• Inner Lining: The inner lining of the helmet is removable and washable. Gently detach the lining from the helmet. Wash it by hand with mild soap and water, then rinse thoroughly. Allow it to air dry completely before reattaching it to the helmet.
• Outer Shell: Clean the outer polycarbonate shell with a soft, damp cloth and mild soap. Avoid using abrasive cleaners, solvents, or harsh chemicals, as these can damage the helmet's materials and finish.
• Straps: Wipe the chin strap and side straps with a damp cloth.
• Rear Light: Wipe the rear light unit with a dry or slightly damp cloth. Ensure no moisture enters the battery compartment.

5.2 Storage

Store the helmet in a cool, dry place away from direct sunlight and extreme temperatures. Avoid storing it in areas where it might be exposed to chemicals, fuels, or solvents, as these can degrade the helmet's materials and compromise its protective capabilities.

6. Troubleshooting

• Helmet feels loose or too tight: Re-adjust the one-hand size adjustment system using the rotary switch at the back of the helmet. Ensure the chin strap is snug but comfortable.
• Rear light not working: Check the batteries in the rear light unit. Replace them if necessary. Ensure the light unit is securely attached.
• Discomfort during wear: Ensure the helmet is positioned correctly on your head, not tilted too far back or forward. Re-adjust the straps and internal padding for optimal comfort. The removable inner lining can be adjusted or cleaned if it's causing discomfort.
• Visor is loose: Ensure the removable visor is correctly inserted and secured into its designated slots.

7. Specifications

8. Safety Information

• Always wear your helmet correctly fitted and securely fastened when cycling.
• A helmet can only protect if it fits well and is worn correctly.
• Inspect your helmet regularly for any signs of damage. If the helmet has sustained an impact, even if no visible damage is apparent, it should be replaced immediately as its protective capabilities may be compromised.
• Do not modify or remove any original components of the helmet.
• Avoid exposing the helmet to extreme heat (e.g., inside a hot car), as this can damage the EPS liner.
• This helmet is designed for cycling and should not be used for other activities that may require different types of head protection.

9. Warranty and Support

Specific warranty details for the Crivit Sports Bicycle Helmet are not provided in this manual. For information regarding warranty coverage, returns, or technical support, please refer to the product packaging, the retailer where the product was purchased, or contact SPEQ GmbH directly through their official support channels.