Henglong 1/16 German Tiger I (3818) & Panther (3819) RC Tank Metal Road Wheels Instruction Manual

1. Introduction

This manual provides detailed instructions for the installation and maintenance of your Henglong 1/16 German Tiger I (Model 3818) and Panther (Model 3819) RC Tank Metal Road Wheels with Rims. These metal road wheels are designed to enhance the performance and durability of your remote-controlled tank model. Please read this manual thoroughly before proceeding with installation.

2. Package Contents

Verify that all components are present and undamaged upon opening the package.

• Set of Metal Road Wheels with Rims (quantity varies by tank model, typically 16-18 per side for Tiger I/Panther)
• Note: Suspension bars are not included with this package.

Figure 1: A complete set of metal road wheels for Henglong 1/16 RC tanks. These wheels are designed to replace the standard plastic road wheels, offering improved durability and performance.

3. Safety Information

• Always disconnect the tank's power source before performing any maintenance or installation.
• Use appropriate tools to avoid damaging components or causing injury.
• Keep small parts away from children and pets.
• Recommended age for installation and use: 14 years and up.

4. Installation Guide

This section outlines the steps to replace your existing road wheels with the new metal road wheels. Ensure you have a clean workspace and necessary tools (e.g., small screwdrivers, pliers).

4.1 Preparation

1. Power off your RC tank and remove the battery.
2. Place the tank on a stable surface, preferably elevated, to easily access the lower chassis and road wheels.
3. Carefully remove the tank tracks. This usually involves detaching a master link or loosening the idler wheel tension. Refer to your tank's primary manual for specific track removal instructions.

4.2 Removing Existing Road Wheels

1. Identify the pins or screws securing each road wheel to its suspension arm.
2. Using appropriate tools, carefully remove these fasteners. Keep track of all screws and small parts.
3. Gently pull each road wheel off its axle.

4.3 Installing New Metal Road Wheels

1. Take one new metal road wheel. Observe its design; the rim is typically integrated.
2. Align the center hole of the metal road wheel with the axle on the suspension arm.
3. Push the wheel onto the axle until it sits flush.
4. Secure the wheel using the original pins or screws removed in step 4.2. Ensure they are tightened sufficiently but do not overtighten, which could strip threads or damage components.
5. Repeat this process for all remaining road wheels on both sides of the tank.

Figure 2: A close-up view of two metal road wheels, highlighting the central hub where the axle connects. This design ensures a secure fit and smooth rotation.

4.4 Post-Installation

1. Once all metal road wheels are installed, reattach the tank tracks. Ensure proper tension as per your tank's manual.
2. Manually rotate the tracks and wheels to check for any binding or obstruction.
3. Reconnect the battery and perform a slow test run to confirm smooth operation.

5. Maintenance

Regular maintenance will prolong the life and performance of your metal road wheels.

• Cleaning: After each use, especially in dusty or muddy conditions, clean the wheels to remove dirt, debris, and grime. A soft brush and damp cloth are usually sufficient. Avoid harsh chemicals.
• Inspection: Periodically inspect the wheels for any signs of wear, damage, or loose fasteners. Ensure the rubber rims (if present) are intact and not peeling.
• Lubrication: The axles and pivot points of the suspension arms may benefit from a small amount of dry lubricant or silicone grease to ensure smooth movement, especially if squeaking occurs. Avoid over-lubrication, which can attract dirt.

6. Troubleshooting

If you encounter issues after installing the metal road wheels, consider the following:

• Wheels not spinning freely: Check for overtightened screws, debris lodged between the wheel and suspension arm, or bent axles. Ensure the wheel is seated correctly.
• Tracks binding or derailing: Verify that all road wheels are installed correctly and are aligned. Check track tension; it might need adjustment after installing new wheels. Ensure no foreign objects are obstructing the track path.
• Unusual noise: Inspect for loose components, friction points, or debris. Lubricate pivot points if necessary.

7. Specifications

8. Warranty and Support

For warranty information or technical support regarding your Henglong metal road wheels, please refer to the original product packaging or contact your retailer. As these are replacement parts, specific warranty terms may vary.

If you have any questions or require further assistance, please reach out to the seller or manufacturer directly.