Copper Fit Rapid Relief Back Support Brace with Hot/Cold Therapy

1. Overview

The Copper Fit Rapid Relief Back Support Brace is designed to provide stabilizing support to the lower back and abdominal muscles, incorporating hot/cold therapy for comfort. It features an adjustable double-band compression belt and includes a reusable gel pack and a lumbar support stabilizing bar.

Image 1.1: Copper Fit Rapid Relief Back Support Brace highlighting key features and benefits.

Key Features:

• Includes 1 compression back belt, 1 gel pack insert, and 1 lumbar support stabilizing bar.
• Adjustable straps with secure double-belt closure for full range of motion and lower back support.
• Lightweight and breathable fabric, suitable for wear under or over clothing.
• Gel pack can be used for hot or cold therapy and is pliable for maximum surface coverage.
• Suitable for men and women ages 13 and up.
• Adjustable to fit waist sizes from 30 inches to 48 inches.

2. Setup and Preparation

2.1. Preparing the Hot/Cold Gel Pack

The included gel pack can be used for either hot or cold therapy. Always refer to the instructions printed directly on the gel pack for precise heating and cooling times, as microwave wattages and freezer temperatures can vary.

For Cold Therapy:

1. Place the gel pack flat in a freezer for at least 2 hours prior to use.
2. Ensure the gel pack is not folded or creased during freezing to maintain its shape and effectiveness.

For Hot Therapy:

1. Wrap the gel pack in a damp cloth or paper towel. This helps maintain pliability and prevents overheating.
2. Place the wrapped gel pack in a microwave.
3. Heat according to the wattage of your microwave and the recommended times on the gel pack. Start with the lowest recommended time and increase in small increments if needed.
4. Carefully remove the gel pack from the microwave. Knead the pack to distribute heat evenly. If additional heat is desired, re-heat in 5-second intervals.

2.2. Inserting Lumbar Support or Gel Pack

The back brace is designed to accommodate either the rigid lumbar support bar or the hot/cold gel pack in its rear pocket.

1. Locate the pocket on the inside of the back brace, centered on the lumbar region.
2. Open the hook-and-loop closure of the pocket.
3. For Lumbar Support: Slide the rigid lumbar support bar into the pocket, ensuring the flat edges are at the bottom and the Copper Fit logo faces outwards. Secure the closure.

Image 2.2: Demonstrates how to insert the rigid lumbar support into the brace's pocket.
4. For Hot/Cold Gel Pack: Carefully insert the prepared hot or cold gel pack into the pocket. Secure the closure.


Image 2.3: Demonstrates how to insert the hot/cold gel pack into the brace's pocket.

3. Operating Instructions

3.1. Wearing the Back Support Brace

1. Position the back brace so that the central lumbar panel (with the inserted support or gel pack) is aligned with your lower spine.
2. Wrap the main belt around your waist. Close the belt, ensuring the right side overlaps the left, for a snug fit that supports your lower back.
3. Gently pull the smaller adjustable straps forward from the sides and secure them to the front of the main belt. This provides additional compression and support.

Image 3.1: Proper application of the back brace, showing how to secure the main belt and adjustable straps.
4. Adjust the tension of the straps to achieve your desired level of compression and comfort. The brace should feel supportive without being overly restrictive.


Image 3.2: The brace provides support during various activities, allowing for mobility.

4. Maintenance and Care

4.1. Brace Care Instructions:

• Hand wash in cold water.
• Air dry.
• Do not bleach.
• Do not tumble dry.
• Do not iron.
• Do not dry clean.

4.2. Gel Pack Care:

Wipe the gel pack clean with a damp cloth as needed. Do not machine wash or dry the gel pack.

5. Troubleshooting

If you experience discomfort or the brace does not provide adequate support, re-adjust the main belt and the smaller adjustable straps to achieve a more secure and comfortable fit. Ensure the lumbar support bar or gel pack is correctly positioned within its pocket.

If issues persist, consult a healthcare professional.

6. Specifications

7. Sizing Information

The Copper Fit Rapid Relief Back Support Brace is designed as one size fits most, accommodating a wide range of waist circumferences.

Image 7.1: Sizing guide for the Copper Fit Rapid Relief Back Support Brace.

Waist Circumference:

For optimal fit, measure your lower back circumference and ensure it falls within the specified range. The adjustable straps allow for a customized and secure fit.

8. Warranty and Support

Specific warranty information is typically provided with your product packaging or can be found on the manufacturer's official website. For any product-related inquiries or support, please contact Copper Fit customer service.

Manufacturer: Copper Fit

Address: Ideavillage Products Corp. 155 Route 46 West, 4th Floor Wayne, NJ 07470

For further assistance, please visit the official Copper Fit Store.