1. Introduction
This manual provides detailed instructions for the safe installation, operation, and maintenance of your Kichler 16228CBR30 Landscape Inground Light. This durable LED fixture is designed for outdoor use, featuring a Centennial Brass finish and a robust construction to withstand environmental elements. Please read this manual thoroughly before installation and retain it for future reference.
2. Important Safety Information
WARNING: Risk of electric shock. Installation must be performed by a qualified electrician in accordance with all local electrical codes and ordinances.
- Disconnect power at the circuit breaker or fuse box before installation or servicing.
- Ensure all electrical connections are secure and comply with local codes and ordinances.
- Do not install this fixture in areas where it may be submerged in water. It is wet-rated but not submersible.
- Do not attempt to modify the fixture. Any modifications may void the warranty and create safety hazards.
- Wear appropriate personal protective equipment (PPE) during installation, including safety glasses and gloves.
- Keep children and pets away from the installation area.
3. Package Contents
Verify that all components are present before beginning installation:
- Kichler 16228CBR30 Inground Light Fixture (with integrated LED)
- Mounting Hardware
- Installation Guide (this document)
4. Installation Instructions
This Kichler inground light is designed for hardwired installation. Professional installation is recommended.
- Prepare the Installation Site: Choose a location that allows for proper drainage and access for wiring. Dig a hole large enough to accommodate the fixture's heavy-duty polymetric sleeve and allow for wiring connections.
- Power Disconnection: Ensure the main power supply to the installation area is turned off at the circuit breaker.
- Wiring: Route the electrical wiring to the installation location. Connect the fixture's wires to the main power supply wires according to local electrical codes. Ensure all connections are secure and properly insulated to prevent moisture ingress. The fixture includes a potted driver and strain relief below for enhanced water protection.
- Fixture Placement: Place the cast brass housing within the heavy-duty polymetric sleeve into the prepared hole. Ensure the top of the fixture is flush with or slightly above ground level to prevent water accumulation.
- Secure the Fixture: Use the provided mounting hardware to secure the fixture in place. Backfill the hole with soil, ensuring the fixture is stable and level.
- Final Inspection: Double-check all connections and ensure the fixture is properly seated and secured.
- Restore Power: Once installation is complete and verified, restore power at the circuit breaker.
Figure 1: Kichler 16228CBR30 Landscape Inground Light. This image displays the overall design of the inground light, featuring its Centennial Brass trim ring and black cylindrical body, ready for installation.
5. Operation
Once installed and power is restored, the Kichler 16228CBR30 light will illuminate. This fixture features the ability to adjust the direction of the light beam (60-degree spread) from outside the fixture, maintaining the factory seal. Gently rotate the internal mechanism as needed to achieve the desired lighting angle for your landscape.
6. Maintenance
The Kichler 16228CBR30 is designed for minimal maintenance.
- Cleaning: Periodically clean the lens and exterior of the fixture with a soft, damp cloth to remove dirt, debris, or mineral deposits. Do not use abrasive cleaners or solvents.
- Inspection: Regularly inspect the fixture for any signs of damage, loose connections, or wear. Ensure the area around the fixture remains clear of excessive foliage or debris that could impede light output or drainage.
- LED Replacement: The LED is integrated and not user-replaceable. If the LED fails, the entire fixture may need replacement.
7. Troubleshooting
Refer to the table below for common issues and their potential solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power supply; Loose wiring connection; Faulty fixture. | Check circuit breaker/fuse; Verify all wiring connections; Contact a qualified electrician or customer support. |
| Light flickers. | Unstable power supply; Loose wiring connection. | Ensure stable power; Check and secure wiring connections. |
| Water inside fixture. | Improper installation; Damaged seals. | Ensure proper drainage around fixture; Verify silicone rubber gaskets are intact; Contact customer support if seals are damaged. |
8. Specifications
| Feature | Detail |
|---|---|
| Brand | Kichler |
| Model Number | 16228CBR30 |
| Material | Brass, Plastic |
| Finish | Centennial Brass |
| Dimensions (L x W x H) | 10.25 x 6.25 x 10.25 inches |
| Item Weight | 10.5 Pounds |
| Light Source Type | Integrated LED |
| Wattage | 10 Watts |
| Voltage | 277 Volts |
| Brightness | 775 Lumens |
| Color Temperature | 3000 Kelvin |
| Beam Angle | 60 Degrees |
| Dimmable | No |
| Moisture Rating | Wet Rated (Water Resistant) |
| Installation Type | In-Ground, Hardwired |
9. Warranty and Customer Support
Warranty Information: All products purchased have a 30-day replacement parts policy to ensure a fully working item. All products are covered under a 1-year warranty when purchased on Amazon. The warranty period begins on the day the product is originally shipped. The warranty covers all items and conditions identified in the original manufacturer's warranty. Specific exclusions include loss and theft, water damage (beyond normal wet rating), customer abuse, and finish deterioration due to UV or coastal exposure.
Customer Support: For technical assistance, warranty claims, or further inquiries, please refer to the contact information provided with your purchase documentation or visit the official Kichler website.