Commercial Electric FSN-15-4K-BZ Integrated LED Floodlight User Manual

Introduction

This manual provides essential instructions for the safe installation, operation, and maintenance of your Commercial Electric FSN-15-4K-BZ Integrated LED Floodlight. This versatile fixture is designed for outdoor security lighting, functioning as both a floodlight and an LED wall pack. Please read this manual thoroughly before installation and retain it for future reference.

Safety Information

WARNING: Risk of electric shock. Disconnect power at the fuse or circuit breaker before installation or servicing. All electrical connections must be in accordance with local and National Electrical Code (NEC) standards. If you are unfamiliar with proper electrical wiring connections, consult a qualified electrician.

• Ensure the supply voltage is correct for the fixture (120V AC).
• Do not install near combustible materials.
• This fixture is rated for wet locations. Ensure all connections are properly sealed to prevent water intrusion.
• Do not attempt to modify the fixture. Integrated LEDs are not replaceable.

Package Contents

Verify that all components are present before beginning installation:

• Integrated LED Floodlight Fixture
• Wall Pack Mounting Arm
• Floodlight Mounting Arm (Knuckle Mount)
• Mounting Hardware (screws, wire nuts, gasket)

Setup and Installation

The FSN-15-4K-BZ offers two primary mounting options: a wall pack mount and a floodlight (knuckle) mount. Choose the appropriate mounting arm for your application.

General Installation Steps:

1. Turn off Power: Locate the circuit breaker controlling the desired installation location and turn off the power.
2. Prepare Wiring: Ensure the electrical box or conduit is properly installed and accessible.
3. Attach Mounting Arm: Secure the chosen mounting arm (wall pack or floodlight) to the fixture.
4. Mount Fixture:
   • For Wall Pack Mount: Attach the wall pack arm directly to a junction box or wall surface using the provided hardware. Ensure a watertight seal with the gasket.
   • For Floodlight Mount: Secure the knuckle mount to a standard junction box or ground stake (not included) as required.
5. Wire Connections: Connect the fixture's wires to the supply wires according to local electrical codes. Typically:
   • Black (Fixture) to Black (Supply) - Live/Hot
   • White (Fixture) to White (Supply) - Neutral
   • Green/Bare Copper (Fixture) to Green/Bare Copper (Supply) - Ground
   Use approved wire nuts for secure connections.
6. Seal Connections: For outdoor installations, ensure all wiring connections and mounting points are properly sealed against moisture.
7. Adjust Aim: Once mounted, adjust the angle of the floodlight to direct illumination as desired.
8. Restore Power: Turn the power back on at the circuit breaker.

Image: The Commercial Electric FSN-15-4K-BZ LED Floodlight demonstrating its two primary mounting configurations: a wall-mounted setup (top left) and a ground-stake or surface-mounted floodlight with a knuckle mount (bottom right). Both units feature the integrated LED light source.

Operating Instructions

The Commercial Electric FSN-15-4K-BZ Integrated LED Floodlight operates by direct electrical connection. Once properly installed and wired to a power source, the fixture will illuminate when power is supplied.

• Power On/Off: Control the light by switching the connected wall switch or circuit breaker ON or OFF.
• Light Output: The integrated LED provides 1500 lumens of white light. There are no adjustable brightness settings on the fixture itself.
• Control Methods (if applicable): While the primary operation is via a standard switch, some installations may integrate this floodlight with external control systems (e.g., photocells, motion sensors, or smart home systems) that manage the power supply to the fixture. Refer to the instructions for any such external control devices for their specific operation.

Maintenance

The FSN-15-4K-BZ LED Floodlight is designed for minimal maintenance.

• Cleaning: Periodically clean the exterior of the fixture with a soft, damp cloth. Do not use abrasive cleaners or solvents. Ensure power is off before cleaning.
• LEDs: The integrated LED light source is designed for long life (50,000+ hours) and is not user-replaceable. Do not attempt to open the sealed LED compartment.
• Inspection: Regularly inspect the fixture and wiring for any signs of damage or wear. Address any issues promptly.

Troubleshooting

Specifications

Warranty and Support

For warranty information or technical support, please refer to the documentation included with your purchase or visit the Commercial Electric official website. Keep your proof of purchase for warranty claims.

Note: This manual is for informational purposes only. Specifications are subject to change without notice.