Introduction
This manual provides essential information for the proper installation, operation, and maintenance of your Irritec RotoDisk T Filter 2 inch 130 Micron. Please read this manual thoroughly before using the product to ensure safe and efficient operation. Keep this manual for future reference.
Product Overview
The Irritec RotoDisk T Filter is a high-quality filtration device designed for irrigation systems. It features a durable PA fiberglass-reinforced body and a 130 micron disk filter element, ensuring effective removal of suspended solids from water. This model is designed for a 2-inch external thread connection and can handle a working pressure of up to 10 bar.
- Model: RotoDisk T Filter (RSL 2" single)
- Connection Size: 2 inch external thread
- Filter Type: Disk
- Filtration Degree: 130 micron
- Material: PA fiberglass-reinforced
- Maximum Working Pressure: 10 bar
- Capacity: 24 m³/h
Image 1: Irritec RotoDisk T Filter 2 inch 130 Micron. This image shows the complete filter unit with its distinctive T-shape and connection points.
Safety Information
Always observe the following safety precautions to prevent injury and damage to the filter:
- Ensure the system pressure does not exceed the maximum working pressure of 10 bar.
- Do not attempt to disassemble the filter while it is under pressure.
- Wear appropriate personal protective equipment (PPE) when installing or maintaining the filter.
- Ensure all connections are properly sealed to prevent leaks.
- Keep out of reach of children.
Setup
Follow these steps for proper installation of the Irritec RotoDisk T Filter:
- Location Selection: Choose a suitable location in your irrigation system, typically after the main water source and before the irrigation zones. Ensure easy access for maintenance.
- System Shut-off: Turn off the main water supply to the irrigation system and relieve any residual pressure.
- Connection: Connect the 2-inch external thread of the filter to the corresponding internal thread of your piping system. Use appropriate sealing tape (e.g., PTFE tape) on the threads to ensure a watertight connection. Tighten connections securely but do not overtighten to avoid damaging the plastic threads.
- Orientation: Install the filter in the correct flow direction, indicated by an arrow on the filter body. The T-shape allows for easy access to the filter element for cleaning.
- System Flush (Optional): After installation, slowly open the main water supply. Allow water to flow through the system and out of an open valve downstream of the filter to flush out any air or debris before operating the full irrigation system.
Operating Instructions
The Irritec RotoDisk T Filter operates passively, filtering water as it flows through the system. No active controls are required for its primary filtration function.
- Once installed and the water supply is on, water will pass through the disk filter element.
- Particles larger than 130 microns will be trapped by the disk element, ensuring cleaner water downstream.
- Monitor the pressure differential across the filter. A significant pressure drop indicates that the filter element may be clogged and requires cleaning.
Maintenance
Regular cleaning of the filter element is crucial for optimal performance and longevity of the Irritec RotoDisk T Filter.
- Shut Down System: Turn off the main water supply to the filter and relieve system pressure.
- Remove Filter Cover: Unscrew the filter cover (usually the bottom part of the T-shape) to access the disk filter element.
- Remove Disk Element: Carefully pull out the disk filter element assembly.
- Clean Disk Element: Separate the individual disks if necessary. Rinse the disks thoroughly under running water to remove trapped particles. A soft brush can be used to dislodge stubborn debris. Ensure all grooves and surfaces are clean.
- Inspect: Inspect the disk element and O-rings for any signs of wear or damage. Replace if necessary.
- Reassemble: Carefully reassemble the disk element, ensuring the disks are correctly stacked. Insert the cleaned disk element back into the filter housing.
- Secure Cover: Replace the filter cover and tighten it securely by hand. Do not overtighten.
- Restore Water Supply: Slowly open the main water supply and check for leaks.
Cleaning Frequency: The frequency of cleaning depends on the water quality. In areas with high sediment, more frequent cleaning will be required. A noticeable drop in water flow or pressure downstream is a key indicator that cleaning is needed.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Reduced water flow/pressure downstream | Clogged filter element | Clean the disk filter element as described in the Maintenance section. |
| Water leaking from filter connections | Loose connections or damaged O-rings/seals | Tighten connections. Inspect and replace O-rings/seals if damaged. Ensure proper use of sealing tape. |
| Filter element difficult to remove/insert | Debris accumulation or incorrect alignment | Ensure system pressure is fully relieved. Clean any debris from the housing. Realign the element carefully. |
Specifications
- Model: Irritec RotoDisk T Filter (RSL 2" single)
- Manufacturer Part Number: 7020560
- Connection Type: 2 inch external thread
- Filter Type: Disk filter
- Filtration Degree: 130 micron
- Body Material: PA fiberglass-reinforced
- Maximum Working Pressure: 10 bar (145 psi)
- Maximum Flow Capacity: 24 m³/h (105 GPM)
- First Available Date: January 15, 2020
Warranty and Support
Specific warranty details for the Irritec RotoDisk T Filter are not provided in the product information. For warranty claims or technical support, please contact your original point of purchase or visit the official Irritec website for regional distributor information.
It is recommended to retain your purchase receipt as proof of purchase.