Introduction
This manual provides instructions for the safe and efficient use of your Navaris Beverage Dispenser. Please read these instructions carefully before initial use and retain them for future reference.
The Navaris Beverage Dispenser is designed for serving a variety of hot and cold beverages, featuring a durable borosilicate glass container, a stainless steel spigot, a bamboo lid, and a sturdy wooden stand.
Image: The Navaris Beverage Dispenser, showcasing its glass body, bamboo lid, stainless steel spigot, and wooden stand, filled with a refreshing pink beverage and lemon slices.
Package Contents
Please verify that all components are present and undamaged:
- 1x Borosilicate Glass Dispenser (1.3 Gallon / 5L capacity)
- 1x Stainless Steel Spigot
- 1x Bamboo Lid with Silicone Seal
- 1x Wooden Stand (Bamboo)
- Gaskets and Fasteners for Spigot Installation
Setup and Assembly
Follow these steps to assemble your beverage dispenser:
- Prepare the Glass Container: Before assembly, ensure the glass container is clean and dry.
- Install the Spigot:
- Insert the threaded part of the stainless steel spigot through the hole in the glass dispenser from the outside.
- On the inside of the dispenser, place a silicone gasket over the threaded part, followed by a metal washer.
- Secure the spigot by screwing on the nut from the inside. Hand-tighten firmly to prevent leaks. Do not overtighten, as this may damage the glass.
- It is recommended to test for leaks with water before filling with your desired beverage.
Image: A visual guide illustrating the correct order of components for spigot installation: spigot, outer gasket, glass wall, inner gasket, washer, and securing nut.
- Position the Stand: Place the wooden stand on a stable, flat surface.
- Place the Dispenser: Carefully lift and place the assembled glass dispenser onto the wooden stand, ensuring it is centered and stable.
Operating Instructions
Filling the Dispenser
- Remove the bamboo lid.
- Pour your desired beverage into the glass dispenser. The borosilicate glass is suitable for both hot and cold drinks.
- Replace the bamboo lid, ensuring the silicone seal creates a snug fit to prevent spills and keep contents fresh.
Image: Detail of the bamboo lid with its metal handle, highlighting the dispenser's capability for both hot and cold beverages due to its borosilicate glass construction.
Dispensing Beverages
- Ensure the dispenser is on a stable surface.
- Place a glass or cup directly under the spigot.
- Push the spigot handle down to open the flow. Release the handle to close the flow.
Image: A hand activating the stainless steel spigot to pour a warm, spiced beverage from the dispenser into a clear glass, demonstrating its use for hot drinks.
Care and Maintenance
Proper care will extend the life of your Navaris Beverage Dispenser:
- Glass Dispenser: The glass part is dishwasher-safe. For best results, place it on the top rack or use a gentle cycle.
- Spigot and Lid: The stainless steel spigot and bamboo lid should be hand-washed with mild soap and warm water. Rinse thoroughly and dry immediately to prevent water spots and preserve the wood.
- Wooden Stand: Wipe the wooden stand with a damp cloth as needed. Do not submerge in water or place in a dishwasher.
- Storage: Store all components clean and dry in a safe place when not in use.
- Avoid: Do not use abrasive cleaners or scouring pads on any part of the dispenser. Do not use the dispenser in conventional or microwave ovens.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Liquid is leaking from the spigot area. | Spigot not installed correctly or gaskets are misplaced/damaged. | Disassemble the spigot and re-install, ensuring both silicone gaskets are properly seated on either side of the glass and the nut is hand-tightened firmly. Inspect gaskets for damage. |
| Beverage flow is slow or stops. | Spigot partially blocked by fruit pulp, ice, or sediment. Spigot not fully open. | Ensure the spigot handle is fully depressed. If using fruit or ice, ensure pieces are not blocking the spigot opening. Clean the spigot thoroughly. |
| Lid does not seal properly. | Silicone seal on the lid is misplaced or dirty. | Check the silicone seal on the bamboo lid for proper placement and cleanliness. Ensure no debris is preventing a tight seal. |
Product Specifications
- Brand: Navaris
- Model: 46785.02
- Material: Borosilicate Glass (Dispenser), Stainless Steel (Spigot), Bamboo (Lid, Stand)
- Capacity: 5 Liters (1.3 US Gallons)
- Product Dimensions (Assembled): Approximately 7.87" L x 7.87" W x 13.39" H (20cm L x 20cm W x 34cm H)
- Item Weight: 7.08 pounds
- Dishwasher Safe: Glass part only. Spigot, lid, and stand require hand-washing.
Image: A diagram illustrating the key dimensions of the dispenser, showing a 20cm diameter for the glass and a total height of 34cm when placed on its stand.
Safety Information
- Always handle the glass dispenser with care to prevent breakage.
- Ensure the dispenser is placed on a stable, level surface to avoid tipping.
- Do not fill with carbonated beverages under high pressure, as this may cause damage.
- Keep out of reach of children when filled with hot liquids.
- Avoid sudden extreme temperature changes to the glass, although borosilicate glass is highly resistant.
Warranty and Support
For warranty information or customer support, please refer to the contact details provided with your purchase or visit the official Navaris website.
Navaris Official Store: Visit the Navaris Store on Amazon
