Introduction
Thank you for choosing the MTX Terminator Series 6.5-inch Component 2-Way Speaker System. This manual provides essential information for the proper installation, operation, and maintenance of your new speakers. Please read this manual thoroughly before installation and retain it for future reference.
The MTX TERMINATOR6S is a 6.5-inch component speaker system designed to deliver enhanced audio performance in your vehicle. It features a durable steel basket, polypropylene cone, and mylar dome tweeter, engineered for clear sound reproduction.
Important Safety Information
Always observe the following safety precautions during installation and operation:
- Disconnect the vehicle's battery before beginning any electrical installation to prevent short circuits.
- Ensure all wiring is properly insulated and secured to prevent damage and electrical hazards.
- Do not install speakers in locations that obstruct vehicle operation or safety features.
- Avoid exposing speakers to excessive moisture or extreme temperatures.
- Prolonged exposure to high volume levels can cause hearing damage. Adjust volume to a safe level.
- This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
Package Contents
Verify that all items are present in your package:
- Two (2) MTX Terminator Series 6.5-inch Component Woofers
- Two (2) MTX Terminator Series Mylar Dome Tweeters
- Two (2) Speaker Grilles
- Mounting Hardware (screws, clips, etc. - typical for speaker installation)
Image: MTX Terminator 6.5-inch component speaker with its protective grille installed, alongside a separate Mylar dome tweeter. The speaker features a red cone and black frame.
Product Features
- Polypropylene Cone: Lightweight yet stiff for accurate sound reproduction.
- Shallow Mounting Depth: Designed for easy installation in various vehicle types.
- 45 Watts RMS Power: Handles continuous power for clear audio output.
- Wide Frequency Response: Delivers sound across a range from 62Hz to 20kHz.
- Durable Steel Basket: Provides structural integrity and reduces resonance.
- Mylar Dome Tweeter: Reproduces crisp high-frequency sounds.
Setup and Installation
Proper installation is crucial for optimal performance. If you are unsure about any steps, consult a professional car audio installer.
Tools and Materials Required:
- Wire strippers/crimpers
- Screwdriver set
- Drill (if new mounting holes are needed)
- Electrical tape or heat shrink tubing
- Speaker wire (if not reusing existing)
- Mounting adapters (if required for your vehicle)
Installation Steps:
- Disconnect Battery: Before starting, disconnect the negative terminal of your vehicle's battery to prevent electrical shorts.
- Remove Existing Speakers: Carefully remove your vehicle's existing speakers or access the desired mounting locations.
- Check Fitment: Ensure the MTX TERMINATOR6S woofers and tweeters fit into the intended locations. The woofer has a shallow mounting depth of 1.63 inches (4.15 cm).
- Mounting the Woofer:
Image: Front view of the MTX Terminator 6.5-inch woofer without its protective grille, showcasing the red polypropylene cone and the MTX Audio logo.
Place the woofer into the mounting hole. Use the provided screws to secure it firmly. If necessary, use mounting adapters for a proper fit. The removable grille incorporates a trim ring that makes all mounting screw heads invisible once installed.
Image: Side profile of the MTX Terminator 6.5-inch speaker, illustrating its shallow mounting depth and the robust steel basket construction.
- Mounting the Tweeter:
Image: Front view of the MTX Terminator Mylar dome tweeter, designed for clear high-frequency sound reproduction.
Install the tweeters in a suitable location, typically near the woofers or in factory tweeter locations. Ensure they are securely mounted. Refer to the tweeter's specific mounting instructions if provided separately.
Image: The MTX Terminator Mylar dome tweeter shown with its approximate dimensions, indicating its compact size for versatile installation.
- Wiring:
Image: Rear view of the MTX Terminator 6.5-inch speaker, displaying the speaker terminals for wiring connections and product specifications.
Connect the positive (+) terminal of the speaker to the positive (+) output of your amplifier or head unit, and the negative (-) terminal to the negative (-) output. Ensure all connections are secure and properly insulated. The TERMINATOR6S speakers have a 4Ω impedance.
For component systems, ensure the tweeters are wired correctly, often in parallel with the woofer or through a passive crossover (if included, though this model states Crossover: NA, implying direct connection or head unit crossover).
- Test System: Reconnect the vehicle's battery. Turn on your audio system and test the speakers at a low volume. Gradually increase the volume to ensure proper operation and sound quality.
- Secure Wiring and Reassemble: Secure all wiring to prevent rattles or damage. Reassemble any removed panels or grilles.
Operating Instructions
Once installed, your MTX Terminator Series speakers are ready for use. Follow these guidelines for optimal performance:
- Volume Control: Adjust the volume on your head unit or amplifier to a comfortable listening level. Avoid prolonged listening at excessively high volumes to prevent speaker damage and hearing loss.
- Equalization: Use your head unit's or amplifier's equalizer settings to fine-tune the sound to your preference. Start with flat settings and make small adjustments.
- Break-in Period: New speakers may require a short break-in period (typically 10-20 hours of normal use) to achieve their full sound potential. During this time, avoid playing them at maximum volume.
- Power Handling: These speakers are rated for 45 Watts RMS. Ensure your amplifier's output matches or is slightly below this rating to prevent damage.
Maintenance
The MTX Terminator Series speakers are designed for durability and require minimal maintenance:
- Cleaning: Use a soft, dry cloth to gently wipe dust or dirt from the speaker grilles and cones. Do not use harsh chemicals or abrasive cleaners.
- Inspection: Periodically check speaker connections for tightness and ensure no wires are frayed or exposed.
- Environmental Protection: While designed for automotive use, avoid direct exposure to extreme elements like heavy rain or direct sunlight for extended periods, which can degrade materials over time.
Troubleshooting
If you experience issues with your speakers, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No Sound from Speakers |
|
|
| Distorted Sound |
|
|
| Weak Bass Response |
|
|
Specifications
| Model | TERMINATOR6S |
| Speaker Type | Component, 2-Way |
| Woofer Diameter | 6.5 Inches |
| Tweeter Diameter | 2.54 Centimeters (1 Inch) |
| RMS Power Handling | 45 Watts |
| Peak Power Handling | 90 Watts |
| Impedance | 4 Ohms (Ω) |
| Frequency Response | 62Hz - 20kHz |
| Sensitivity | 85.5dB (2.83V/1m) |
| Woofer Cone Material | Polypropylene |
| Woofer Mounting Depth | 1.63 inches (4.15 cm) |
| Grille Included | Yes |
Warranty and Support
MTX Audio products are designed and manufactured to the highest quality standards. This product comes with a Limited Warranty. Please refer to the official MTX Audio website or your purchase documentation for specific warranty terms and conditions, including duration and coverage details.
For technical support, troubleshooting assistance, or warranty claims, please contact MTX Audio customer service through their official website or the retailer where the product was purchased.
Online Resources: www.mtx.com
