myownid RFID Card Reader 13.56MHz Mifare: UID Reader/Writer & Programmer (Model RFID Reader01) Instruction Manual

Introduction

This manual provides comprehensive instructions for the myownid RFID Card Reader (Model RFID Reader01). It covers device setup, operational procedures for reading and writing 13.56MHz Mifare cards, maintenance guidelines, and troubleshooting tips to ensure optimal performance. Please read this manual thoroughly before using the device.

Package Contents

Image: Contents of the product package, including the RFID reader, USB cable, a configuration card, and several Mifare cards.

• 1x myownid RFID Card Reader (Model RFID Reader01)
• 1x USB Cable
• 5x Mifare Cards
• 1x Configuration Card
• Software CD/USB drive (containing drivers and software)

Specifications

Setup

1. Connect the Device: Connect the RFID Reader to your computer using the provided USB cable. The device should be recognized automatically.
2. Install Drivers and Software:

   For full functionality, especially for writing operations, install the necessary drivers and software from the included CD/USB drive or download them from the manufacturer's website. The software for writing Mifare Classic 1K/4K card sector data is only supported on Windows.
3. Select Operating Mode: The reader has three integrated working modes, which can be switched using the provided configuration card. Refer to the "Data Format List and Reader Function Settings" section for details on output formats and reader function settings.

Operating Instructions

1. Reading Mifare Card UID (Keyboard Input Mode)

In this mode, the reader acts as a keyboard input device, outputting the UID of 14443A Mifare cards directly into any text editor or application. This includes Mifare Classic, UltraLight, Mifare Plus, Mifare Desfire, and Mifare N-TAG/card emulation.

1. Ensure the reader is in the correct UID Reader mode (configured via the config card).
2. Open a text editor (e.g., Notepad, Word) or any application where you want the UID to appear.
3. Place a compatible 13.56MHz Mifare card on the reader. The UID will be automatically typed into the active input field.

Image: The myownid RFID Card Reader connected to a computer via its USB cable, ready for operation.

2. Writing Mifare Card Data (Windows Software Only)

The writer mode utilizes USB 2.0 communication and dedicated Windows software to program sector data on Mifare Classic 1K/4K cards. This mode is essential for advanced operations like cloning or modifying card data.

1. Ensure the reader is connected to a Windows PC and the writing software is installed.
2. Open the Mifare writing software (e.g., "FissaiD MF Writer" or similar).
3. Place the Mifare Classic 1K/4K card you wish to write to on the reader.
4. Follow the software interface to read existing data, modify sectors, and then write the new data to the card.

Image: Screenshot of the FissaiD MF Writer software interface, showing options for reading and writing Mifare Classic 1K/4K card sectors.

3. Supported Card Types

Image: A visual list detailing the types of cards supported by the RFID reader.

• USB Reader Only (Read UID of Below Cards):
  • Mifare Classic / EV1 S50/S70
  • Mifare Plug S/SE/X/EV1
  • Mifare DESFire EV1/EV2
  • Ultralight Nano/EV1/C
  • N-TAG NFC (card emulation)
• USB Programmer (Sector Writer, Only Support cards as):
  • Mifare Card S50 (1K memory)
  • Mifare Card S70 (4K memory)

  Note: USB programmer mode requires Windows software.

4. Data Format List and Reader Function Settings

Image: A table illustrating various data output formats and settings for the RFID reader, including options for QWERTY/AZERTY keyboard layouts and buzzer control.

The reader supports 28 output formats for UID reading. These formats can be configured using the provided configuration card. Key settings include:

• UID Output Formats: Various combinations of 8-digit, 6-digit, 4-digit, and 2-digit hexadecimal or decimal values, with options for suffix (-R for reverse, -E for enter after card number).
• Keyboard Layout: Options for QWERTY (29 E) and AZERTY (30 F) layouts.
• Buzzer Control: Enable or disable the audible buzzer.
• USB Programmer: Setting for USB Programmer mode (-USB).

To switch modes or settings, read the configuration card with the desired setting. The new setting will be displayed each second. Once the desired format is confirmed, unplug and replug the reader. The setting is stored and will be effective upon next use.

Maintenance

• Cleaning: Use a soft, dry cloth to clean the device. Avoid using abrasive cleaners or solvents.
• Storage: Store the reader in a cool, dry place away from direct sunlight and extreme temperatures.
• Handling: Handle the device with care to prevent physical damage. Avoid dropping or subjecting it to strong impacts.

Troubleshooting

Warranty and Support

For warranty information, technical support, or further assistance, please refer to the contact details provided with your purchase or visit the official myownid website. Keep your purchase receipt as proof of purchase for warranty claims.