1. Safety Information
Please read all safety instructions before installation and use. Failure to follow these instructions may result in injury or damage to the product.
- Tripping Hazard: The strip door may pose a tripping hazard. Exercise caution when passing through.
- Children and Pets: Keep out of reach of children and pets to prevent choking hazards from small parts or entanglement.
- Heat and Flames: Avoid exposing the PVC material to excessive heat or open flames, as it can release harmful chemicals and deform.
- Ventilation: Ensure adequate ventilation during installation and initial use, as PVC products may have a temporary odor.
- Sharp Edges: Handle strips carefully during installation to avoid cuts from edges.
2. Product Components
The Strivide Strip Door Curtain Kit includes all necessary components for assembly and installation.
Image Description: An illustration showing the components of the Strivide Strip Door Kit. It includes USDA/NSF approved PVC door strips (shown as a roll of clear material), hanger mounting #14 x 2.75" metal screws, and a universal wall or jamb mount hanger made of 14 gauge galvanized steel. The image also highlights "MADE IN USA".
- PVC Strips: Clear, smooth, 8" wide x .08" thick PVC strips, pre-punched for easy hanging. USDA and NSF approved.
- Universal Mount Hanger: Heavy-duty 14 gauge galvanized steel hanger, suitable for both jamb and wall mounting.
- Hanger Mounting Screws: #14 x 2.75" Hex TEK screws for secure installation.
- Installation Instructions: EZ 10-minute install instructions (textual and visual guides).
3. Setup & Installation
Follow these steps for proper installation of your Strivide PVC Strip Door Curtain Kit. Ensure you have the correct tools before beginning.
3.1. Determine Mounting Method
The universal hanger allows for two primary installation methods: Wall Mount or Under Lintel (Jamb) Mount. The choice depends on your door opening and available space.
Video Description: This video, titled "Strip Curtain Door Hanger Guide" by Restaurant Cooler Gaskets, explains the differences between wall mount and under lintel mount installations for strip doors. It provides visual guidance on how each method is applied to a door frame.
3.2. Installation Steps (General)
- Measure Door Opening: Accurately measure the width and height of your door opening.
- Mount Hanger: Secure the universal hanger to the wall or under the lintel using the provided mounting screws. Ensure it is level and firmly attached.
- Prepare Strips: The PVC strips are pre-punched. If necessary, trim strips to the desired length, ensuring they reach the floor with a slight overlap.
- Hang Strips: Slide the pre-punched PVC strips onto the hanger mounting studs following the specified overlap pattern (e.g., 50% overlap for this model).
- Secure Retainer Plate: Install the strip retainer plate over the strips and secure with the provided nuts.
Image Description: A person's hands are shown carefully attaching clear PVC strips to a metal hanger system. The strips have pre-punched holes that fit onto studs on the hanger, demonstrating the ease of assembly.
Image Description: A diagram illustrating the installation process for a strip door. It shows both jamb mount and wall mount options for the hanger, along with a table detailing the number of strips required for different door widths and overlap percentages (50%, 67%, 100%).
4. Operating Instructions
The Strivide PVC Strip Door is designed for passive operation, providing an environmental barrier while allowing easy passage.
- Passage: Simply walk or drive through the strips. The flexible PVC material will part and then fall back into place, maintaining the seal.
- Visibility: The clear strips offer high visibility, allowing users to see oncoming traffic or obstacles. Always ensure clear visibility before proceeding.
- Environmental Control: The strips are designed to reduce noise, minimize energy loss, and keep out pests, insects, and dust.
Image Description: A yellow forklift is shown driving through a clear PVC strip door in an industrial setting. The strips flex to allow passage, demonstrating the door's functionality for heavy traffic.
5. Maintenance
Regular maintenance ensures the longevity and optimal performance of your strip door.
- Cleaning: Clean PVC strips periodically with mild soap and water. Avoid abrasive cleaners or solvents that can damage the material.
- Inspection: Regularly inspect strips for signs of wear, cracking, or damage. Replace damaged strips promptly to maintain effectiveness.
- Hanger Check: Ensure the hanger system remains securely fastened and free from corrosion. Tighten any loose screws as needed.
- Alignment: Verify that strips hang evenly and maintain their overlap. Adjust if necessary to prevent gaps.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Strips do not seal properly. | Incorrect overlap, damaged strips, or improper installation. | Check overlap percentage, replace damaged strips, re-align hanger. Refer to "Strip Door Curtain Overlap Guide" video. |
| Strips are stiff or cracking in cold temperatures. | Incorrect PVC material for low-temperature environments. | Ensure Low-Temp PVC strips are used for freezer applications. This model is "Clear Smooth" and suitable for ambient temperatures. |
| Excessive air movement through the door. | Insufficient overlap or strip width for the environment. | Consider a higher overlap percentage or wider/thicker strips if the environment has high wind or air pressure. Refer to "Strip Door Curtain Overlap Guide" video. |
| Difficulty passing through strips. | Strips are too thick or too wide for pedestrian traffic. | For pedestrian-only traffic, narrower and lighter strips might be more suitable. This model is designed for general use. |
Video Description: This video, titled "Strip Door Curtain Overlap Guide" by Restaurant Cooler Gaskets, explains how different overlap percentages affect the sealing capability of PVC strip doors. It demonstrates 50% and 100% overlap configurations.
Video Description: This video, titled "Strip Curtain Door Strip Width Guide" by Restaurant Cooler Gaskets, discusses the appropriate strip widths and thicknesses for various door opening heights and traffic types. It helps in selecting the correct strip size for optimal performance.
7. Specifications
- Model: Strivide 48x96 Clear Smooth PVC Strip Door Kit
- Dimensions: 48" Width x 96" Height (4 ft x 8 ft)
- Strip Material: Polyvinyl Chloride (PVC)
- Strip Size: 8" Wide x .08" Thick
- Overlap: 50%
- Color: Clear Smooth
- Hanger Material: 14 Gauge Galvanized Steel
- Mounting Type: Universal (Jamb or Wall Mount)
- Special Features: Waterproof, USDA/NSF Approved, Anti-Static, Fire Retardant, Wind Resistant, Noise Reduction.
- Assembly Required: Yes
- Included Components: Pre-punched PVC strips, Universal Mount Hanger, Hanger Mounting Screws, Installation Instructions.
- Usage: Indoor Industrial Partitioning (suitable for warehouses, factories, supermarkets, malls, freezers, coolers).
8. Warranty & Support
For warranty information or technical support, please contact Strivide customer service. This product is manufactured in the USA by a small business committed to quality and customer satisfaction.
- Customer Service: Refer to your purchase documentation or the manufacturer's website for contact details.
- Returns: Standard 30-day refund/replacement policy applies as per purchase terms.
