1. Introduction
Thank you for choosing the SVAVO Automatic Soap Dispenser V-410. This touchless, wall-mounted dispenser is designed to provide a hygienic and convenient handwashing experience in various settings. Please read this manual thoroughly before installation and use to ensure proper operation and longevity of your device.
2. Product Features
- Touchless Operation: Equipped with a smart motion infrared sensor for sanitary, no-touch dispensing.
- Non-Drip Design: The dispensing valve prevents dripping and reduces mess after each use.
- Versatile Application: Suitable for bathrooms, kitchens, laundry rooms, offices, hotels, hospitals, restaurants, schools, clinics, and salons. Compatible with various liquid soaps, dish soaps, body lotions, and shampoos (ensure liquid is not too thick).
- Space-Saving Wall Mount: Designed to save countertop space with easy wall installation.
- Energy Efficient: Operates on 4 AA-size batteries (not included) for extended periods.
- Ultra-Large Capacity: 600ml (21 fl.oz) reservoir reduces the frequency of refilling.
3. Package Contents
Please check the package for the following items:
- SVAVO Automatic Soap Dispenser Unit
- Mounting Hardware (screws, wall anchors)
- Security Key for Lid (if applicable)
- User Manual
4. Setup
4.1. Battery Installation
- Locate the battery compartment at the bottom of the dispenser.
- Open the battery compartment cover.
- Insert 4 AA-size batteries (not included), ensuring correct polarity (+/-).
- Close the battery compartment cover securely.
Figure 1: Correctly installing 4 AA batteries into the dispenser.
4.2. Mounting the Dispenser
- Choose a suitable wall location, ensuring the sensor will be 8-12 inches above the countertop or sink.
- Detach the back mounting plate from the dispenser unit.
- Mark the desired screw positions on the wall using the mounting plate as a template.
- Drill pilot holes if necessary and insert wall anchors.
- Secure the mounting plate to the wall using the provided screws.
- Slide the dispenser unit onto the mounted plate until it clicks securely into place.
Figure 2: The SVAVO Automatic Soap Dispenser installed on a wall, highlighting its compact dimensions (4.3"L x 3.9"W x 6.5"H) and the recommended installation height of 8-12 inches above the counter.
Figure 3: The touchless infrared sensor allows for hygienic soap dispensing, activating when a hand is placed beneath the nozzle, promoting cleanliness.
4.3. Filling the Dispenser
- Unlock the top lid using the provided security key (if applicable) or by gently pulling up the back of the lid.
- Pour your desired liquid soap, shampoo, body wash, or other compatible liquid into the reservoir. Do not overfill.
- Close the lid securely. You may use the key to lock it if desired, especially in public or family settings to prevent tampering.
Figure 4: The dispenser is versatile and can be filled with various liquid products, including hand soap, shampoo, body wash, dish soap, and even makeup remover. Ensure the liquid is not too thick for optimal dispensing.
5. Operating Instructions
5.1. Power On/Off
Locate the power switch at the bottom of the dispenser. Slide it to the 'ON' position to activate the device. The indicator light may blink to confirm it is on. Slide to 'OFF' when not in use for extended periods.
5.2. Dispensing Soap
Once powered on, place your hand approximately 0-10 cm (0-4 inches) beneath the infrared sensor located at the bottom of the dispenser. The sensor will detect your hand and automatically dispense approximately 1ml of liquid. Remove your hand to stop dispensing.
6. Maintenance
6.1. Refilling
Monitor the liquid level through the transparent reservoir. When the level is low, follow the steps in Section 4.3 to refill the dispenser.
6.2. Cleaning
- Wipe the exterior of the dispenser with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Avoid submerging the dispenser in water or allowing water to enter the battery compartment or sensor area.
- If the nozzle becomes clogged, gently clean it with a small brush or toothpick.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Dispenser does not activate or dispense. | Low or dead batteries; Power switch is OFF; Sensor obstructed; Reservoir empty. | Replace batteries; Turn power switch ON; Clear any obstructions from the sensor; Refill reservoir. |
| Soap leaks from nozzle. | Soap too thin; Dispenser overfilled; Internal component issue. | Use thicker liquid soap; Do not overfill; Contact customer support if problem persists. |
| Dispensing is inconsistent or slow. | Liquid too thick; Nozzle clogged; Low batteries. | Dilute liquid soap with water (if compatible); Clean the nozzle; Replace batteries. |
| Lid does not lock securely. | Improper alignment; Damaged locking mechanism. | Ensure lid is properly aligned before locking; Contact customer support if mechanism is damaged. |
8. Specifications
- Color: Black
- Material: Plastic
- Product Dimensions: 4.3"L x 3.9"W x 6.5"H
- Shape: Rectangular
- Liquid Volume: 600 Milliliters (21 fl.oz)
- Power Source: 4 x AA Batteries (not included)
- Item Weight: 1.06 pounds
- Model Number: V-410
- UPC: 717332777707
9. Warranty and Support
SVAVO offers lifetime technical support for this product. If you encounter any issues with your touchless soap dispenser, please feel free to contact us via the Amazon email system. We are committed to assisting you until you are satisfied.
10. Product Videos
Video 1: This video demonstrates the features and installation process of the SVAVO Automatic Soap Dispenser, including battery insertion and touchless operation.
Video 2: A detailed demonstration of mounting the SVAVO Automatic Soap Dispenser on a wall and its touchless dispensing function.
Video 3: This video provides an overview of the SVAVO Automatic Soap Dispenser, showcasing its design and functionality.
