1. Introduction
This instruction manual provides essential information for the proper use, maintenance, and sterilization of the OSUNG Dental Elevator EL301 2.7mm. This instrument is designed for professional dental use only and should be handled by licensed professionals and practices with appropriate training.
Important Safety Notice: Always follow standard dental safety protocols and local regulations when using dental instruments. Improper use can lead to injury or damage to the instrument.
2. Product Overview
The OSUNG Dental Elevator EL301 2.7mm is a high-quality instrument used to loosen teeth from the periodontal ligament, facilitating tooth extraction. It is constructed from durable stainless steel and features a non-slip handle for secure grip.
Key Features:
- Stainless Steel construction for durability and hygiene.
- Non-slip handle for enhanced grip and control during procedures.
- Autoclavable at 135 degrees Centigrade for effective sterilization.
Image 2.1: Three OSUNG Dental Elevators EL301 2.7mm, showcasing the instrument's design and quantity in a typical package.
Image 2.2: A single OSUNG Dental Elevator EL301 2.7mm, presented at an angle to highlight the handle and shaft design.
Image 2.3: Close-up view of the working tip of the OSUNG Dental Elevator EL301 2.7mm, showing its precise design for periodontal ligament separation.
3. Setup
Before initial use, and prior to each subsequent use, the instrument must be thoroughly cleaned and sterilized according to the guidelines provided in Section 5.
- Inspect the instrument for any signs of damage, corrosion, or dullness. Do not use damaged instruments.
- Ensure the instrument is free from any manufacturing residues or packaging materials.
- Proceed with cleaning and sterilization as outlined in the Maintenance section.
4. Operating Instructions
The OSUNG Dental Elevator EL301 2.7mm is intended for the careful and controlled separation of the tooth from its surrounding periodontal ligament. This procedure requires professional skill and knowledge.
General Usage Guidelines:
- Always use appropriate personal protective equipment (PPE).
- Gently insert the working tip into the periodontal space.
- Apply controlled, rotational, or levering forces to gradually loosen the tooth.
- Avoid excessive force to prevent fracture of the tooth or surrounding bone.
- Regularly assess the tooth mobility during the process.
5. Maintenance and Sterilization
Proper cleaning and sterilization are crucial for maintaining the longevity and hygienic integrity of the OSUNG Dental Elevator EL301 2.7mm.
Cleaning:
- Immediately after use, remove gross debris by rinsing under running water.
- Clean the instrument using a soft brush and an appropriate enzymatic cleaner or detergent. Ensure all surfaces, especially the working tip and handle texture, are thoroughly cleaned.
- Rinse thoroughly with distilled or deionized water to remove all cleaning solution residues.
- Dry the instrument completely to prevent water spots and corrosion.
Sterilization:
The OSUNG Dental Elevator EL301 2.7mm is autoclavable.
- Place the cleaned and dried instrument in a suitable sterilization pouch or tray.
- Autoclave at 135 degrees Centigrade (275 degrees Fahrenheit) for the recommended cycle time according to your autoclave manufacturer's instructions.
- Allow the instrument to cool completely within the sterile packaging before handling or storage.
- Store sterilized instruments in a clean, dry, and protected environment.
6. Troubleshooting
This section addresses common concerns regarding the dental elevator.
Issue: Instrument appears dull or damaged.
- Solution: Do not use dull or damaged instruments. Such instruments can compromise patient safety and procedural effectiveness. Replace the instrument if it shows signs of wear, bending, or corrosion.
Issue: Difficulty in sterilization.
- Solution: Ensure proper cleaning before sterilization. Residual debris can hinder effective sterilization. Verify your autoclave is functioning correctly and that the correct temperature and cycle times are being used.
7. Specifications
Detailed specifications for the OSUNG Dental Elevator EL301 2.7mm.
Image 7.1: OSUNG Dental Elevator EL301 2.7mm displayed alongside a ruler, indicating its approximate length and tip size.
| Specification | Detail |
|---|---|
| Model Number | EL301 |
| Tip Size | 2.7mm |
| Material | Stainless Steel |
| Sterilization Method | Autoclavable at 135°C (275°F) |
| UPC | 849194032394 |
| Manufacturer | OSUNG |
8. Warranty and Support
For any questions regarding the OSUNG Dental Elevator EL301 2.7mm, including warranty information, product support, or to inquire about different quantities, please contact your authorized OSUNG distributor or the seller directly. Ensure to provide the model number (EL301) and UPC (849194032394) for efficient assistance.
You can visit the official Osung Store for more information: Osung Store on Amazon