Introduction
The IKEA Ribba Frame is designed to display your favorite photos, prints, or artwork. This manual provides essential information for the safe and proper use, setup, and maintenance of your frame. Please read these instructions carefully before use and retain them for future reference.
Figure 1: IKEA Ribba Frame (Model 303.784.25) with mat.
Safety Information
- Handle with care to avoid damage to the frame or injury.
- Ensure proper wall mounting hardware is used for the wall type to prevent the frame from falling.
- Keep out of reach of small children to prevent accidental injury from falling objects or small parts.
- Avoid placing the frame in direct sunlight or high humidity, which can damage the artwork and frame material.
Package Contents
Verify that all components are present before beginning assembly or setup:
- 1 x IKEA Ribba Frame (12x16 inches, black)
- 1 x White Mat (for 8x10 inch picture, can be removed for 12x16 inch picture)
- 1 x Plastic Front Protection
- 1 x Backing Board
- Hanging hardware (e.g., metal hangers, screws/nails not typically included but frame has hanging points)
Setup
1. Unpacking the Frame
- Carefully remove the frame from its packaging.
- Inspect the frame for any damage. If damaged, do not proceed with setup and contact customer support.
2. Inserting Artwork or Photo
- Lay the frame face down on a clean, flat surface.
- Carefully bend or rotate the metal clips holding the backing board in place.
- Remove the backing board and the plastic front protection.
- Peel off any protective film from both sides of the plastic front protection.
- Decide whether to use the included white mat. The mat is suitable for an 8x10 inch picture. Without the mat, the frame can hold a 12x16 inch picture.
- Place your artwork or photo face down onto the plastic front protection (with or without the mat).
- Place the backing board on top of your artwork, ensuring it is flush with the frame edges.
- Secure the metal clips back into position to hold the backing board firmly.
Figure 2: Detail of the frame's construction and finish.
3. Displaying the Frame
The Ribba frame can be displayed on a wall or placed on a flat surface.
Wall Mounting:
- The frame includes pre-attached metal hangers on the backing board for both horizontal and vertical orientation.
- Choose the desired orientation and mark the wall where the hanging points will be.
- Install appropriate wall anchors and screws/nails (not included) suitable for your wall material.
- Carefully hang the frame onto the installed hardware, ensuring it is level and secure.
Figure 3: Example of multiple Ribba frames mounted on a wall.
Tabletop Display:
- For tabletop display, simply lean the frame against a wall or support on a flat surface such as a shelf, desk, or cabinet.
- Ensure the surface is stable and the frame is not at risk of falling.
Figure 4: Ribba frame used for tabletop display.
Operating
The IKEA Ribba Frame is designed for static display. Its primary operation involves changing the displayed artwork or photo.
Changing Artwork:
- Remove the frame from the wall or tabletop.
- Lay the frame face down on a clean, flat surface.
- Unbend or rotate the metal clips holding the backing board.
- Remove the backing board and the current artwork.
- Insert the new artwork or photo.
- Replace the backing board and secure the metal clips.
- Re-hang or re-position the frame as desired.
Maintenance
Cleaning the Frame:
- Wipe the frame and plastic front protection with a dry cloth or a cloth dampened with water.
- For stubborn marks on the plastic front protection, use a mild, non-abrasive cleaner specifically designed for plastics.
- Avoid using harsh chemicals, abrasive cleaners, or solvents, as these can damage the frame's finish or the plastic front.
- Ensure the frame is completely dry before re-hanging or placing it.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Picture does not fit. | Incorrect picture size or mat usage. | Ensure your picture is 12x16 inches (without mat) or 8x10 inches (with mat). Trim picture if necessary, or remove mat. |
| Frame hangs crooked. | Improperly installed wall hardware or uneven hanging points. | Use a level to ensure wall hardware is aligned. Adjust hanging points on the frame if possible, or re-install wall hardware. |
| Plastic front appears scratched or cloudy. | Protective film not removed, or improper cleaning. | Ensure protective film is removed from both sides. Clean with a soft, damp cloth and avoid abrasive materials. |
| Backing board is loose. | Metal clips not fully secured. | Press down firmly on all metal clips to ensure they are fully engaged and holding the backing board tightly. |
Specifications
| Feature | Detail |
|---|---|
| Brand | IKEA |
| Model Number | 303.784.25 |
| Color | Black |
| Frame Dimensions | 12 x 16 inches (30 x 40 cm approx.) |
| Picture Size (with mat) | 8 x 10 inches (20 x 25 cm approx.) |
| Frame Material | Plastic |
| Front Protection Material | Plastic (Polystyrene) |
| Mounting Type | Wall Mount / Tabletop (leaning) |
| Item Weight | 1.1 pounds (0.5 kg) |
Warranty and Support
For information regarding warranty coverage or product support, please refer to the official IKEA website or contact IKEA customer service directly. Keep your proof of purchase for any warranty claims.
For further assistance, visit: IKEA Customer Service