Zeutch UDL_FA
Zeutch Homelife LED Motion Sensor Bar Light UDL_FA Instruction Manual
Model: UDL_FA | Brand: Zeutch
Introduction
This manual provides detailed instructions for the proper setup, operation, and maintenance of your Zeutch Homelife LED Motion Sensor Bar Light. Please read this manual thoroughly before using the product to ensure optimal performance and longevity.
Setup
Package Contents
- 1 x Homelife LED Motion Sensor Bar Light
- 1 x Magnetic Strip with Adhesive
- 1 x USB Charging Cable
Charging the Device
Before initial use, fully charge the LED Motion Sensor Bar Light. The device features a built-in 1500mAh rechargeable battery.
- Locate the USB charging port on the side of the light bar.
- Connect the provided USB charging cable to the light bar and a compatible USB power source (e.g., computer, wall adapter).
- A red indicator light will illuminate during charging. Once fully charged, the indicator light will turn blue.
Image: Charging the LED Motion Sensor Bar Light. The red light indicates charging, and a blue light indicates a full charge.
Installation
The LED Motion Sensor Bar Light is designed for easy, tool-free installation using its magnetic mounting system.
- Clean the surface where you intend to install the light. Ensure it is dry and free of dust or grease.
- Peel off the protective film from the adhesive side of the magnetic strip.
- Firmly press the magnetic strip onto the desired surface for approximately 30 seconds.
- Attach the LED Motion Sensor Bar Light to the magnetic strip. The built-in magnets will hold it securely in place.
Image: Attaching the magnetic strip to a surface and then mounting the light bar.
Video: A demonstration of the easy installation process and various applications of the LED Motion Sensor Bar Light.
Operating Instructions
Power and Mode Selection
The light bar features a button for power control and mode selection. There are three primary operating modes:
- MODE 1: Motion Sensor Mode (Green indicator light flashes once) - The light will automatically turn on when motion is detected in low-light conditions and turn off after approximately 20 seconds of no motion.
- MODE 2: Always On Mode (Red indicator light flashes once) - The light will remain continuously on, regardless of motion or ambient light.
- MODE 3: OFF - The light is turned off.
To switch between modes, short press the button. To activate the Always On Mode from any other mode, long press the button for 3 seconds.
Image: The light bar showing its three color modes and control button.
Light Color Modes
The light offers three color temperature options to suit different preferences and environments:
- White Light: Bright, cool illumination.
- Warm Light: Soft, yellowish illumination.
- Natural Light: A balanced blend of white and warm light.
To cycle through the color modes, short press the button while the light is in Always On Mode.
Motion Sensor Functionality
In Motion Sensor Mode, the light detects movement within a 10-foot range and a 120-degree angle. It is designed to activate only in dark environments to conserve battery life. The light will automatically turn off after approximately 20 seconds if no further motion is detected.
Image: Diagram explaining the motion sensor's detection range and behavior in different lighting conditions.
Video: Demonstrates the motion sensor light activating in various dark environments like cabinets and under beds.
Maintenance
Battery Information
The light bar is equipped with a 1500mAh rechargeable battery. Battery life varies depending on the selected mode:
- Motion Sensor Mode: Approximately 2-3 months of use.
- Always On Mode: Approximately 11 hours of continuous use.
Regular charging is recommended to maintain optimal battery performance. Refer to the 'Charging the Device' section for instructions.
Image: Feature comparison highlighting battery capacity and duration.
Cleaning
To clean the light bar, gently wipe it with a soft, dry cloth. Avoid using abrasive cleaners or solvents, as these may damage the finish or electronic components. Ensure the device is turned off and disconnected from any power source before cleaning.
Troubleshooting
| Issue | Possible Cause | Solution |
|---|---|---|
| Light does not turn on in Motion Sensor Mode. | Sufficient ambient light; battery low; sensor obstructed. | Ensure the environment is dark enough for activation. Charge the device. Check if the motion sensor is clear of obstructions. |
| Light turns off too quickly or stays on too long. | Sensor sensitivity variation; continuous motion. | The sensor has a fixed 20-second auto-off timer. Ensure no continuous motion is within range if it stays on. If it turns off too quickly, reposition the light or ensure the sensor is not obstructed. |
| Light does not charge. | Faulty cable or power source; charging port issue. | Try a different USB cable and power source. Ensure the cable is fully inserted into the charging port. |
| Light output is dim. | Low battery. | Recharge the device fully. |
Product Specifications
| Feature | Detail |
|---|---|
| Brand | Zeutch |
| Model Name | UDL_FA (also known as UDL_20) |
| Product Dimensions | 7.5"L x 1.18"W x 0.78"H |
| Item Weight | 4.97 ounces |
| Material | Acrylonitrile Butadiene Styrene, Aluminum |
| Light Source Type | LED (20 LEDs) |
| Light Color | Warm White (3 Color Modes: White, Warm, Natural) |
| Brightness | 200 Lumens |
| Wattage | 2 watts |
| Voltage | 3.7 Volts |
| Power Source | Rechargeable Battery (1500mAh) |
| Installation Type | Magnetic Mount |
| Special Features | Motion Sensor, Always On Mode, Energy Efficient, Night Lights |
| Connectivity Protocol | Infrared |
| Water Resistance Level | Not Water Resistant |
| UPC | 784237683150, 767421509320 |
Warranty and Support
Zeutch provides a Lifetime Warranty for this product. We are committed to ensuring your satisfaction with our products.
For any product quality issues or support inquiries, please contact us via email. We aim to offer a free replacement after confirmation of any valid product quality issue.
Contact Information: Refer to your purchase documentation or the official Zeutch store for specific contact details.
Image: Zeutch company logo.
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.