Pyle PLUTV43BTA 4-inch Off-Road Bluetooth Waterproof Speaker System User Manual

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Pyle PLUTV43BTA 4-inch Off-Road Bluetooth Waterproof Speaker System. Please read this manual thoroughly before use to ensure proper functionality and longevity of the product. This amplified speaker system is designed for use in various 12V vehicles, including ATVs, UTVs, golf carts, and boats, offering robust audio performance in outdoor environments.

Safety Information

Observe the following safety guidelines to prevent damage to the unit or injury to yourself:

• Ensure the power source is 12V DC. Incorrect voltage can damage the unit.
• Do not attempt to open or service the unit yourself. Refer all servicing to qualified personnel.
• Avoid exposing the unit to extreme temperatures or direct sunlight for extended periods.
• Securely mount the speakers to prevent them from becoming loose during vehicle operation.
• Ensure all wiring connections are properly insulated and protected from water and debris.

Package Contents

Verify that all items are present in the package:

• (1) 4-inch Amplified Main Speaker
• (1) 4-inch Passive Support Speaker
• Speaker Connection Wires (6.5 ft.)
• Wire Butt Connectors (16-22 AWG)
• EVA Mounting Pads

Image: Contents of the Pyle PLUTV43BTA speaker system box, including two speakers, EVA mounting pads, wire butt connectors, and speaker wires.

Setup and Installation

Follow these steps for proper installation of your speaker system:

Mounting the Speakers

1. Unbolt the Mounting Bracket: Use a screwdriver to loosen and remove the screws securing the mounting bracket to the speaker.
2. Slide Buckle with Rubber Pad: Place the rubber pad around the desired mounting bar (e.g., roll-bar, roll-cage). Position the buckle of the mounting bracket over the rubber pad.
3. Attach Screw to Lock the Buckle: Re-attach the mounting bracket to the speaker and tighten the screws securely, ensuring the speaker is firmly attached to the bar.

Image: Step-by-step diagram illustrating the mounting process for the speakers, showing how to secure them to a bar using the provided brackets and rubber pads.

Wiring Connections

The system includes one amplified (main) speaker and one passive (support) speaker. Connect them as follows:

1. Connect Speaker Wires: Use the provided speaker connection wires to link the passive speaker to the amplified main speaker. Ensure correct polarity (+ to + and - to -).
2. Connect Speaker Power Cable: Securely connect the speaker power cable from the amplified main speaker to a 12V DC power source on your vehicle. It is recommended to connect through an ignition-switched circuit or a dedicated switch to prevent battery drain. Use the provided wire butt connectors for secure and insulated connections.
3. Auxiliary Input (Optional): If using an external device via the 3.5mm Aux Input Jack, connect your device to this port on the main speaker.

Image: Detail from the installation diagram showing the connection of speaker wires and the speaker power cable to the main speaker.

Operating Instructions

Powering On/Off

The speaker system will power on when connected to a 12V power source. If wired to an ignition-switched circuit, it will power on/off with your vehicle's ignition. If wired to a separate switch, use the switch to control power.

Bluetooth Pairing

1. Ensure the speaker system is powered on.
2. On your mobile device (smartphone, tablet, etc.), enable Bluetooth.
3. Search for available Bluetooth devices. The network name for the speaker system is PYLEUSA.
4. Select "PYLEUSA" to pair your device. Once paired, you will hear a confirmation tone, and you can begin streaming audio wirelessly.
5. The wireless range is approximately 30+ feet.

Image: Illustration of a smartphone successfully paired with the Pyle speaker system via Bluetooth, displaying the network name 'PYLEUSA'.

Auxiliary Input

To play audio from devices without Bluetooth, connect them directly to the 3.5mm Aux Input Jack on the main speaker using a standard audio cable (not included).

Maintenance

To ensure the longevity and optimal performance of your Pyle PLUTV43BTA speakers:

• Cleaning: Use a soft, damp cloth to clean the speaker surfaces. Avoid harsh chemicals or abrasive cleaners.
• Water Exposure: While the speakers are waterproof (IP-X5 rated), prolonged submersion is not recommended. After exposure to saltwater or mud, rinse with fresh water to prevent corrosion.
• Connections: Periodically check all wiring connections for tightness and signs of wear or corrosion.

Image: A Pyle speaker enduring water splashes, highlighting its robust, weather-resistant design suitable for outdoor environments.

Troubleshooting

Specifications

Warranty and Support

This product comes with a limited warranty. For detailed warranty information or technical support, please refer to the official Pyle website or contact their customer service. Keep your purchase receipt as proof of purchase.

For further assistance, visit: www.pyleusa.com