1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Pomelotree LED Window Lights. These LED modules are designed for various applications, including storefront advertising, home decoration, and under-cabinet lighting. Please read this manual thoroughly before installation and use to ensure proper function and safety.
2. Package Contents
Verify that all components are present in the package:
- 2 x LED modules (2 strands, 20 pieces each, total 40 pieces)
- 1 x Remote controller
- 1 x Receiver
- 1 x Power Cord
3. Specifications
| Feature | Specification |
|---|---|
| Type | 6 LED modules light (5054 SMD) |
| Material | PVC Plastic |
| LED Quantity | 6 LEDs per module, 240 LEDs total (40 modules) |
| Beam Angle | 120 degrees |
| Waterproof Level | IP65 |
| Working Voltage | DC 12V |
| Power | 0.25W per LED |
| Luminous Flux | 780-900lm per 20 modules |
| Module Dimension | 76 x 10 x 5 mm (2.99 x 0.39 x 0.20 inch) |
| Length per Strand | 10 ft (with extension wire) |
| Total Length | 20 ft (2 strands) |
| Working Temperature | -20~60℃ |
4. Setup and Installation
Follow these steps to properly set up and install your LED window lights:
4.1 Preparing the Wires
If you need to cut the strands or connect individual modules, you may need to prepare the wires. The modules can be cut between them. Ensure you cut the connect line between the modules.
- Cut a length of approximately 5cm of the wire cover.
- Strip the wire ends. You can use a wire stripping tool or carefully melt the ends with a lighter (wear gloves for safety).
- Twist the exposed wire ends together. For thin wires, fold and twist again to ensure a secure connection.
- Wrap the connection with insulated tape to prevent short circuits.
4.2 Connection Methods
There are two primary ways to connect the LED modules:
4.2.1 Parallel Connection (Recommended)
Parallel connection ensures that all modules receive the same voltage, resulting in uniform brightness across the entire length of the lights.
4.2.2 Series Connection (Not Recommended for Long Strands)
In a series connection, the voltage drops across each module, which can lead to a gradual decrease in brightness along the length of the lights. This method is generally not recommended for long installations where uniform brightness is desired.
Warning: Pay special attention to the positive and negative poles of the wire to avoid short circuits during connection.
4.3 Mounting the LED Modules
The LED modules come with sticky self-adhesive tape on the back for easy installation. Simply peel off the backing and press the module firmly onto a clean, dry surface. For additional security, especially on uneven surfaces or for permanent installations, the modules also feature optional screw holes, allowing you to hang them with screws (screws not included).
5. Operation
Once installed and connected to the power source, the LED window lights can be controlled using the included remote controller and receiver.
5.1 Connecting the Remote System
- Connect the LED module strand to the receiver.
- Connect the power cord to the receiver.
- Plug the power cord into a standard electrical outlet.
5.2 Using the Remote Controller
The remote controller allows you to turn the lights on/off, adjust brightness, and potentially change modes (if applicable to your specific remote model). Point the remote towards the receiver for optimal control.
Note: The specific functions of the remote control buttons may vary slightly. Refer to the remote's markings for detailed functionality.
6. Maintenance
To ensure the longevity and optimal performance of your Pomelotree LED Window Lights, follow these maintenance guidelines:
- Cleaning: Gently wipe the LED modules with a soft, dry cloth to remove dust and dirt. Avoid using abrasive cleaners or solvents.
- Water Exposure: While the modules are IP65 waterproof, ensure that the power connections (receiver and power cord) are protected from direct water exposure, especially during heavy rain or snow.
- Connection Check: Periodically inspect all wire connections to ensure they are secure and free from corrosion or damage. Re-tape any exposed wires if necessary.
- Storage: If storing the lights for an extended period, disconnect them from power, clean them, and store them in a cool, dry place away from direct sunlight.
7. Troubleshooting
If you encounter issues with your LED window lights, refer to the following troubleshooting guide:
| Problem | Possible Cause | Solution |
|---|---|---|
| Lights do not turn on. | No power supply; loose connection; faulty power adapter/receiver. | Check if the power cord is securely plugged into the outlet and receiver. Ensure all module connections are tight. Test the outlet with another device. |
| Some modules are dim or off. | Loose connection to specific modules; series connection causing voltage drop; damaged module. | Inspect connections to the affected modules. Ensure you are using a parallel connection for uniform brightness. If a module is damaged, it may need replacement. |
| Remote control not working. | Remote battery low/dead; receiver out of range; obstruction between remote and receiver. | Replace remote battery. Ensure remote is pointed directly at the receiver and within range. Remove any obstructions. |
| Lights flicker. | Unstable power supply; loose connection; faulty module. | Check power source stability. Secure all connections. If flickering persists, a module or power component might be faulty. |
8. Safety Information
- Always disconnect power before performing any installation, maintenance, or troubleshooting.
- Do not exceed the specified voltage (DC 12V).
- Ensure all electrical connections are properly insulated to prevent short circuits and electrical hazards.
- Do not submerge the power adapter or receiver in water. Only the LED modules are rated IP65 waterproof.
- Keep out of reach of children.
- Avoid direct eye exposure to the LED light source for prolonged periods.
9. Warranty and Support
For warranty information or technical support, please contact Pomelotree customer service through your original point of purchase or visit the official Pomelotree website. Please have your product model (5054 LED Modules) and ASIN (B07J65TY3L) ready when contacting support.