SmartBidet SB-100R Electric Bidet Seat User Manual

Introduction

The SmartBidet SB-100R Electric Bidet Seat is designed to provide enhanced hygiene, comfort, and convenience for elongated toilets. This manual provides detailed instructions for installation, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your bidet seat.

Important Safety Precautions

Please read all instructions carefully before installation and use. Failure to follow these instructions could result in electric shock, fire, or injury.

• Ensure the power outlet is properly grounded and matches the bidet's voltage requirements.
• Do not immerse the bidet seat, power cord, or plug in water or other liquids.
• Unplug the bidet seat from the electrical outlet when not in use or before cleaning.
• Do not allow children or individuals with reduced physical, sensory, or mental capabilities to operate the bidet without supervision.
• Avoid using abrasive cleaners, solvents, or strong chemicals on the bidet seat, as they may damage the surface.

Package Contents

Verify that all components are present before beginning installation:

• SmartBidet SB-100R Electric Bidet Seat
• Remote Control with Wall Mount
• Water Supply Hose
• T-Valve Connector
• Mounting Plate and Bolts
• User Manual (this document)

Figure 1: SmartBidet SB-100R Electric Bidet Seat and Remote Control.

Installation Guide

Pre-Installation Checklist

• Ensure you have an elongated toilet. Refer to the dimensions diagram below.
• Confirm a GFCI (Ground Fault Circuit Interrupter) electrical outlet is available within reach of the bidet's power cord.
• Turn off the water supply to your toilet before starting.

Installation Steps

1. Remove Existing Toilet Seat: Lift the hinge covers, unscrew the mounting bolts, and remove the old toilet seat and lid.
2. Install T-Valve: Turn off the water supply to the toilet. Flush the toilet to empty the tank. Disconnect the existing water supply hose from the toilet tank. Install the provided T-valve onto the toilet tank's fill valve. Reconnect the original water supply hose to the bottom of the T-valve.
3. Attach Mounting Plate: Place the mounting plate over the toilet's bolt holes. Insert the mounting bolts through the plate and toilet holes, securing them from underneath with nuts. Adjust the plate position as needed.
4. Slide Bidet Seat On: Align the SmartBidet seat with the mounting plate and slide it forward until it clicks securely into place.
5. Connect Water Supply: Connect one end of the provided bidet water supply hose to the T-valve and the other end to the bidet seat's water inlet. Ensure all connections are hand-tightened, then use a wrench for a final snug fit, being careful not to overtighten.
6. Connect Power: Plug the bidet seat's power cord into the GFCI electrical outlet.
7. Restore Water Supply: Slowly turn on the water supply to the toilet. Check for any leaks.
8. Test Functions: Once installed, test all bidet functions as described in the Operating Instructions section.

Figure 2: SmartBidet SB-100R installed on a toilet.

Figure 3: SmartBidet SB-100R Dimensions for Elongated Toilets.

Operating Your SmartBidet

The SmartBidet SB-100R features an intuitive remote control and a side panel for easy operation. The bidet activates when a user sits on the seat, thanks to its skin sensor.

Remote Control Overview

Figure 4: Remote Control Functions.

• Rear Wash: For posterior cleansing.
• Feminine Wash: A gentler, wider wash for feminine hygiene.
• Turbo Wash: The strongest, most concentrated wash for posterior cleansing.
• Water Pressure: Adjusts the intensity of the water spray.
• Water Temperature: Adjusts the temperature of the wash water.
• Seat Temperature: Adjusts the temperature of the heated seat.
• Nozzle Position: Moves the nozzle forward or backward for optimal cleansing.
• Oscillate: Moves the nozzle back and forth during washing for a wider cleaning area.
• Eco Mode: Reduces power consumption when the bidet is not in active use.

Wash Functions

To activate a wash function, ensure you are seated on the bidet. Press the corresponding button on the remote control (Rear, Feminine, or Turbo). The wash will begin automatically.

Figure 5: Heated Water Spray.

Temperature and Pressure Adjustment

Use the dedicated buttons on the remote control to increase or decrease water pressure, water temperature, and seat temperature. LED indicators on the bidet seat provide visual feedback for these settings.

Figure 6: Heated Seat Feature.

Nozzle Position and Oscillation

Adjust the nozzle's position using the arrow buttons on the remote. Press the 'Oscillate' button to enable the nozzle to move back and forth during the wash cycle for a more thorough clean.

Eco Mode

Activate Eco Mode to conserve energy. The bidet will automatically lower the seat temperature and water heating when not in active use for an extended period. Press any wash button to exit Eco Mode.

Care and Maintenance

Cleaning the Bidet Seat

• Unplug the bidet seat before cleaning.
• Wipe the exterior surfaces with a soft, damp cloth and a mild, non-abrasive detergent.
• Do not use harsh chemicals, abrasive cleaners, or scrub brushes, as they can damage the finish.
• The quick-release seat design allows for easy removal for thorough cleaning of the toilet and bidet.

Nozzle Cleaning and Replacement

The stainless steel nozzle features a self-cleaning function that activates before and after each use. For manual cleaning or replacement of the nozzle cap:

• Ensure the bidet is unplugged.
• Gently pull the nozzle cap forward to remove it.
• Clean the nozzle cap with a soft brush and mild soap, or replace it with a new one.
• Reattach the nozzle cap by pushing it firmly back into place until it clicks.

Figure 7: Replaceable Nozzle Cap.

Troubleshooting

If you encounter issues with your SmartBidet SB-100R, refer to the table below for common problems and solutions.

Product Specifications

Figure 8: SmartBidet SB-100R Dimensions (Metric).

Warranty and Customer Support

The SmartBidet SB-100R Electric Bidet Seat comes with a 1-year manufacturer warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use.

For warranty claims, technical assistance, or any questions not covered in this manual, please contact SmartBidet customer support:

• Website: Visit the official SmartBidet website for support resources.
• Email: Refer to your purchase documentation for direct email support.
• Phone: Refer to your purchase documentation for customer service phone numbers.

Please have your model number (SB-100R) and proof of purchase ready when contacting support.