American Lighting H2-Jump.5 6-inch Jumper for Hybrid 2 LED Lighting Systems

1. Introduction

The American Lighting H2-Jump.5 is a 6-inch jumper cable designed to connect segments of the American Lighting Hybrid 2 LED lighting system. This accessory facilitates flexible installation by allowing gaps or turns between LED strip sections, ensuring continuous illumination. This manual provides essential information for the safe and correct installation and use of the H2-Jump.5 jumper.

2. Product Overview

The H2-Jump.5 jumper is a critical component for customizing Hybrid 2 LED lighting layouts. It provides a 6-inch flexible connection between two Hybrid 2 LED light sections, allowing for navigation around obstacles or extending runs without direct contact. The jumper includes necessary middle connectors, power connectors, and end caps for a complete and secure installation.

Figure 1: American Lighting H2-Jump.5 6-inch Jumper. This image displays the white 6-inch jumper cable with clear, threaded connectors on both ends, designed for connecting sections of Hybrid 2 LED lighting. The cable is marked with specifications: CUL E199762 SJTW 2X0.824mm²(18AWG) 300V 105°C FT1 YIN YU APVC.

3. Package Contents

• 1 x H2-Jump.5 6-inch Jumper Cable
• Middle Connector(s)
• Power Connector(s) (if applicable for initial connection)
• End Cap(s) (for sealing open ends of LED strips)

4. Safety Information

Please read and understand all safety instructions before installation and use. Failure to follow these instructions may result in electric shock, fire, or other hazards.

• Disconnect Power: Always ensure power is disconnected at the circuit breaker before installing or servicing any electrical components.
• Qualified Personnel: Installation should be performed by a qualified electrician or trained personnel familiar with electrical wiring and lighting systems.
• Indoor Use Only: This product is designed for indoor applications as indicated by its specifications. Do not expose to moisture or outdoor elements unless explicitly rated for such use.
• Voltage Compatibility: Ensure the jumper is used only with American Lighting Hybrid 2 LED systems and compatible power sources.
• Secure Connections: All connections must be tight and secure to prevent electrical hazards and ensure proper operation.
• Avoid Damage: Do not bend, twist, or pull the cable excessively. Inspect the cable for any damage before installation.

5. Setup and Installation

Follow these steps to properly install the H2-Jump.5 jumper with your Hybrid 2 LED lighting system:

1. Plan Layout: Before beginning, plan the desired layout of your Hybrid 2 LED strips, identifying where the 6-inch jumper will be needed to bridge gaps or navigate corners.
2. Prepare LED Strips: Ensure the ends of the Hybrid 2 LED strips are clean and free from debris. If cutting the LED strip, ensure cuts are made only at designated marks and that the end is properly prepared for connection.
3. Connect Jumper to First Strip: Take one end of the H2-Jump.5 jumper. Align the pins of the jumper's connector with the corresponding receptacles on the end of the first Hybrid 2 LED strip. Gently push the connector firmly into place. Once seated, twist the threaded collar of the jumper connector to secure it to the LED strip, ensuring a watertight and secure connection.
4. Connect Jumper to Second Strip: Repeat the previous step for the other end of the H2-Jump.5 jumper, connecting it to the start of the next Hybrid 2 LED strip segment. Ensure both connections are fully tightened.
5. Secure Wiring: Route the jumper cable neatly and secure it using appropriate clips or channels to prevent strain or damage.
6. Power On: Once all connections are made and secured, restore power to the circuit. Test the LED lighting system to ensure continuous and proper illumination across all connected segments.

6. Operation

The H2-Jump.5 jumper is a passive component designed to facilitate electrical continuity between Hybrid 2 LED strip segments. Once correctly installed, it requires no direct operation. The connected LED strips will function as a single, continuous unit, controlled by their respective power supply and controller (if applicable).

7. Maintenance

The H2-Jump.5 jumper requires minimal maintenance. Regular inspection can help ensure its longevity and safe operation:

• Visual Inspection: Periodically check the jumper cable and its connections for any signs of wear, damage, or loose connections.
• Cleaning: If necessary, gently wipe the cable and connectors with a dry, soft cloth to remove dust or debris. Do not use harsh chemicals or abrasive cleaners.
• Environmental Conditions: Ensure the jumper remains in an environment consistent with its indoor rating, free from excessive moisture or extreme temperatures.

8. Troubleshooting

If the LED lighting system does not function correctly after installing the H2-Jump.5 jumper, consider the following:

• No Light on Connected Segment:
  • Verify that power is supplied to the entire system.
  • Check both ends of the H2-Jump.5 jumper to ensure they are securely and correctly connected to the LED strips. Loose connections are a common cause of failure.
  • Inspect the jumper cable for any visible damage or kinks that might interrupt the electrical flow.
  • Ensure the LED strips themselves are functional and correctly installed.
• Intermittent Lighting:
  • Tighten all threaded collars on the jumper connectors.
  • Check for any movement or strain on the cable that might cause intermittent contact.

If issues persist, disconnect power and consult a qualified electrician or contact American Lighting customer support.

9. Specifications

10. Warranty and Support

For warranty information or technical support regarding your American Lighting H2-Jump.5 jumper, please refer to the official American Lighting website or contact their customer service directly. Keep your purchase receipt for warranty claims.

American Lighting Contact Information:
Please visit the American Lighting Store on Amazon or their official website for the most current support details.