E-link Hardened Industrial Gigabit PoE+ Injector User Manual

1. Introduction

This user manual provides detailed instructions for the installation, operation, and maintenance of the E-link Hardened Industrial Gigabit PoE+ Injector (Model: PoE-LNK-INJ301-fba). This device is designed to provide both data and power over a single Ethernet cable to Power over Ethernet (PoE) compatible devices, simplifying network deployment in various industrial environments.

2. Safety Information

• Ensure the input voltage is within the specified range of 12~48V DC.
• Do not expose the device to water or excessive humidity.
• Avoid placing the device in areas with extreme temperatures or direct sunlight.
• Disconnect power before performing any maintenance or installation procedures.
• This device is designed for industrial use and features 6KV lightning protection. However, proper grounding is always recommended.

3. Package Contents

Please verify that all items are present in your package:

• E-link Hardened Industrial Gigabit PoE+ Injector (PoE-LNK-INJ301-fba)
• User Manual (this document)
• DIN-Rail mounting kit (pre-installed or separate)
• Wall-mount screws (if applicable)

4. Product Overview

The E-link Industrial Gigabit PoE+ Injector is a robust device designed for reliable power and data transmission in harsh environments. It features a durable aluminum case and supports a wide operating temperature range.

Figure 4.1: Front view of the E-link Industrial Gigabit PoE+ Injector.

4.1. Key Features

• Gigabit Ethernet Ports: Supports 10/100/1000Mbps data rates.
• PoE+ Output: Provides up to 30W of power, compliant with IEEE802.3af/at standards.
• Wide Voltage Input: Operates with 12~48V DC input.
• Hardened Design: Durable aluminum case, wide operating temperature range (-40°C to 80°C).
• Lightning Protection: Built-in 6KV lightning protection.
• Flexible Installation: Supports DIN-Rail and Wall-Mount installation.

4.2. Port and LED Indicators

Figure 4.2: Port and LED indicators overview.

• PoE OUT Port: RJ45 port for connecting to a PoE-powered device (PD). Delivers both data and 30W PoE output.
• Ethernet Port: RJ45 port for connecting to a non-PoE network device (e.g., switch, router).
• V+/V- Terminal Block: 12~48V DC power input.
• PWR LED: Indicates power status. (Green: Power On)
• PoE LED: Indicates PoE status. (Green: PoE active)

5. Setup and Installation

The PoE Injector supports both DIN-Rail and Wall-Mount installation methods.

5.1. DIN-Rail Installation

The device comes with a pre-installed DIN-Rail clip. To install:

1. Align the top of the DIN-Rail clip with the top edge of the DIN-Rail.
2. Push the device firmly downwards until the clip snaps securely onto the DIN-Rail.
3. Ensure the device is stable and does not wobble.

Figure 5.1: Example of DIN-Rail mounting.

5.2. Wall-Mount Installation

If DIN-Rail is not available, you can wall-mount the device using screws (not always included, check package contents).

1. Mark the positions for the mounting screws on the wall using the device's mounting holes as a template.
2. Drill pilot holes if necessary and insert wall anchors.
3. Secure the device to the wall using appropriate screws.

5.3. Wiring and Connections

1. Power Connection: Connect a 12~48V DC power source to the V+/V- terminal block. Ensure correct polarity.
2. Data Input: Connect an Ethernet cable from your non-PoE network device (e.g., switch, router) to the Ethernet port on the injector.
3. PoE Output: Connect an Ethernet cable from the PoE OUT port on the injector to your PoE-powered device (e.g., IP camera, VoIP phone, wireless access point).

Figure 5.2: Typical application scenario for the PoE Injector.

6. Operating Instructions

Once the device is properly installed and connected, it will automatically begin operation. The E-link PoE+ Injector functions as a plug-and-play device, requiring no complex configuration.

6.1. Power Over Ethernet (PoE) Functionality

The injector combines data from the Ethernet port with power from the DC input and delivers both to the connected PoE-powered device via the PoE OUT port. This eliminates the need for separate power outlets for your PoE devices.

The injector supports IEEE802.3af (15.4W) and IEEE802.3at (30W) standards, automatically detecting and providing the necessary power to compatible devices.

6.2. LED Status Indicators

• PWR LED (Green):
  • On: Device is powered on.
  • Off: Device is powered off or no power input.
• PoE LED (Green):
  • On: PoE power is being supplied to the connected device.
  • Off: No PoE power is being supplied.

7. Maintenance

The E-link PoE+ Injector is designed for minimal maintenance. Follow these guidelines to ensure optimal performance:

• Keep the device clean and free from dust. Use a soft, dry cloth for cleaning.
• Ensure proper ventilation around the device to prevent overheating.
• Regularly check cable connections for secure fit.
• Do not attempt to open or repair the device yourself. Refer to qualified personnel for service.

8. Troubleshooting

9. Specifications

10. Warranty and Support

E-link products are backed by international certifications such as ISO, ROHS, CE, and FCC. For specific warranty details and technical support, please contact E-link directly or the authorized reseller from whom you purchased the product. You can visit the official E-link store on Amazon for more information: E-link Amazon Store.