Introduction
Thank you for choosing the EVERVIEW EV2700MD Full Motion TV Wall Mount. This manual provides detailed instructions for safe installation, operation, and maintenance of your TV wall mount. Please read this manual thoroughly before installation and keep it for future reference. This mount is designed for most 37-75 inch flat panel TVs, supporting a maximum weight of 132 lbs (60 kg) and compatible with VESA patterns up to 600x400mm.
Package Contents
Before installation, please verify that all components listed below are present and undamaged. If any parts are missing or damaged, contact EVERVIEW customer service immediately.
- 1x EVERVIEW EV2700MD TV Wall Mount
- 1x Standard Mounting Hardware Kit (pre-labeled bags)
- 1x User Manual
- 1x 3-Axis Magnetic Bubble Level
- 5x Cable Ties
Specifications
| Feature | Specification |
|---|---|
| Model Number | EV2700MD |
| Screen Size Compatibility | 37 - 75 inches |
| Weight Capacity | Up to 132 lbs (60 kg) |
| VESA Compatibility | 200x100, 200x200, 300x200, 300x300, 400x200, 400x300, 400x400, 500x300, 600x200, 600x400mm |
| Tilt Adjustment | -12° to +3° |
| Swivel Adjustment | Up to 90° left or right |
| Profile from Wall | 3 inches (retracted) to 14.4 inches (extended) |
| Wall Stud Spacing | Fits 12/16 inch wood studs |
| Material | Alloy Steel |
| Color | Black |
Safety Information
WARNING: Failure to read and follow these instructions may result in serious personal injury, property damage, or voiding of your warranty. If you do not understand these instructions or have doubts about the safety of the installation, please contact a qualified installer or EVERVIEW customer service.
- This product is intended for installation on wood stud walls only. Do not install on drywall alone or metal studs.
- Ensure the mounting surface can safely support the combined weight of the mount and your TV.
- Do not exceed the maximum weight capacity of 132 lbs (60 kg).
- Use only the provided mounting hardware. Do not use screws that are too long or too short.
- Always use a stud finder to locate the center of wood studs.
- Two people are recommended for installation to ensure safety.
- Keep children and pets away during installation.
Setup & Installation
For a visual guide, please watch the official installation video below:
This video provides a step-by-step guide for installing the EVERVIEW EV2700MD Full Motion TV Wall Mount.
Step 1: Assemble the Wall Plate and Arms
Begin by assembling the main wall plate and the articulating arms. Follow the diagrams in the included user manual to connect the arm sections securely using the provided screws and hex key. Ensure all connections are tight.
Step 2: Attach TV Brackets to Your TV
Carefully place your TV face down on a soft, clean surface. Identify the VESA mounting holes on the back of your TV. Select the appropriate screws and washers from the hardware kit that fit your TV's VESA holes. Attach the two vertical TV brackets to the back of your TV, ensuring they are centered and securely fastened. Do not overtighten.
This diagram illustrates various VESA mounting patterns and the compatible ranges for the EVERVIEW TV wall mount. Always check your TV's VESA pattern before installation to ensure compatibility.
Step 3: Mark and Drill Pilot Holes on the Wall
Using a stud finder, locate the center of two adjacent wood studs where you intend to mount the TV. Mark the stud locations. Hold the assembled wall plate against the wall at your desired height, using the included bubble level to ensure it is perfectly horizontal. Mark the drilling points through the wall plate's holes. Drill pilot holes at the marked locations. Ensure the drill bit size matches the recommended size in the manual for your wall type.
This image shows a TV wall mounted with the EVERVIEW mount, highlighting its suitability for wood studs with spacing between 8 and 16 inches. Proper stud location is crucial for secure installation.
Step 4: Mount the Wall Plate to the Wall
Align the wall plate with the drilled pilot holes. Insert the lag bolts with washers into the holes and tighten them securely using a socket wrench. Do not overtighten, but ensure the mount is firmly attached to the wall.
Step 5: Hang the TV onto the Wall Mount
With assistance, carefully lift your TV and hook the attached TV brackets onto the arms of the wall mount. Ensure the TV is securely seated on the mount. Tighten the safety screws on the bottom of the TV brackets to prevent accidental dislodgement.
Operation
The EVERVIEW EV2700MD Full Motion TV Wall Mount offers flexible viewing options:
- Extension/Retraction: Gently pull the TV away from the wall to extend the arms up to 14.4 inches, or push it back to retract it to a slim 3-inch profile.
- Tilt: Loosen the tilt adjustment knobs on the TV brackets, adjust the screen to your desired angle (-12° to +3°), and then tighten the knobs to secure the position.
- Swivel: Gently push the TV left or right to swivel it up to 90° in either direction, allowing for optimal viewing from different seating positions.
- Level Adjustment: The mount allows for a +/-3° level adjustment after installation to ensure your TV is perfectly horizontal. Use the provided hex key to adjust the leveling screws on the TV plate.
This diagram illustrates the EVERVIEW TV wall mount's articulation, tilt, swivel, and extension capabilities, allowing for a customized viewing experience.
Maintenance
Regular maintenance helps ensure the longevity and safe operation of your TV wall mount:
- Cleaning: Wipe the mount with a soft, dry cloth. Avoid abrasive cleaners or solvents that could damage the finish.
- Check Connections: Periodically check all screws and bolts to ensure they remain tight. Re-tighten if necessary, but do not overtighten.
- Inspect for Wear: Inspect the mount for any signs of wear, damage, or corrosion. If any issues are found, contact customer service.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| TV is not level | Minor misalignment during installation. | Use the +/-3° level adjustment feature. Loosen the leveling screws, adjust the TV, and re-tighten. |
| Mount feels unstable | Screws not fully tightened or incorrect stud placement. | Ensure all lag bolts are securely tightened into the wood studs. Verify stud location. Do not exceed weight capacity. |
| Difficulty with tilt/swivel | Tilt knobs too tight or mechanism needs lubrication. | For tilt, loosen the tilt adjustment knobs. For swivel, ensure no cables are obstructing movement. A small amount of silicone-based lubricant can be applied to moving joints if necessary. |
Warranty & Support
The EVERVIEW EV2700MD Full Motion TV Wall Mount comes with a 5-year friendly US-based customer service. For any questions, concerns, or assistance with installation or product issues, please contact EVERVIEW customer support. Keep your purchase receipt for warranty claims.
