SATMAXIMUM Full Motion TV Wall Mount Bracket

Introduction

This manual provides detailed instructions for the safe and proper installation and operation of your SATMAXIMUM Full Motion TV Wall Mount Bracket. This bracket is designed to securely hold LED, LCD, and Plasma displays ranging from 32 to 47 inches, with VESA patterns up to 400x400mm. It offers full motion capabilities, including swivel, tilt, and extension, allowing you to achieve optimal viewing angles from various positions in your room.

Important Safety Information

WARNING: Failure to read and follow these instructions may result in serious personal injury, property damage, or voiding your warranty. If you do not understand these instructions or have doubts about the safety of the installation, please contact customer support or a qualified installer.

• Do not install this product on walls that are not structurally sound or on walls made of drywall alone. Ensure the mounting surface can safely support the combined weight of the mount and your TV.
• Verify your TV's VESA pattern and weight are within the specified limits of this mount (VESA 100x100mm to 400x400mm, Max Load Capacity: 35 Kg / 77 lbs).
• Always use the provided mounting hardware. If your installation requires different hardware, consult a professional.
• This product is intended for indoor use only.
• Keep children and pets away during installation.
• Periodically check that the mount is secure and all fasteners are tight.

Package Contents

Please check to ensure all components are present and undamaged. If any parts are missing or defective, contact SATMAXIMUM customer service for assistance.

• Wall Plate Assembly
• TV Bracket Arms (2x)
• Mounting Hardware Kit (various screws, washers, spacers for TV and wall)
• Bubble Level
• Instruction Manual

Setup and Installation

Before beginning, ensure you have the necessary tools (e.g., drill, stud finder, screwdriver, wrench) and understand all steps. It is highly recommended to have at least two people for installation.

Step 1: Pre-Installation Checks

• Check TV Compatibility: Verify your TV's weight (max 35 kg / 77 lbs) and VESA mounting pattern (100x100mm to 400x400mm).
• Identify Wall Type: This mount is suitable for wood stud walls or solid concrete/brick walls. Do not install on drywall without wood studs.
• Determine Mounting Location: Choose a location that provides optimal viewing and allows for the full range of motion of the mount.

Step 2: Attach TV Brackets to TV

1. Carefully place your TV face down on a soft, clean surface.
2. Identify the correct screws, washers, and spacers from the hardware kit that fit your TV's mounting holes.
3. Attach the two TV bracket arms to the back of your TV using the selected hardware. Ensure the hooks on the bracket arms face upwards and are securely tightened.

Image: TV bracket arms attached to the back of a television, illustrating the VESA mounting points.

Step 3: Mount Wall Plate to Wall

1. Using a stud finder, locate the center of the wood studs in your desired mounting location. Mark the drill holes. For concrete/brick walls, use a masonry drill bit and anchors (not included, consult professional).
2. Hold the wall plate against the wall, aligning the drill holes with your marks. Use the included bubble level to ensure the wall plate is perfectly horizontal.
3. Drill pilot holes into the wall.
4. Secure the wall plate to the wall using the appropriate lag bolts and washers. Tighten all bolts firmly.

Image: The full motion TV wall mount extended, demonstrating its articulating arm design.

Step 4: Hang TV on Wall Plate

1. With assistance, carefully lift the TV with the attached brackets and hook them onto the wall plate.
2. Ensure the TV is securely seated on the wall plate.
3. Tighten the safety screws located on the bottom of the TV bracket arms to prevent accidental dislodging.

Operating the Mount

This full motion mount allows for flexible TV positioning.

• Swivel: Gently push or pull the TV to swivel it left or right up to 180 degrees (actual range depends on TV size and wall distance).
• Tilt: Loosen the tilt adjustment knobs on the TV bracket arms, adjust the TV to your desired tilt angle (up to ±15°), and then re-tighten the knobs to secure the position.
• Extension: Pull the TV away from the wall or push it back towards the wall to adjust the viewing distance (Wall Distance: 2.6" - 16.7").

Maintenance

Regular maintenance ensures the longevity and safe operation of your TV mount.

• Cleaning: Wipe the mount with a soft, dry cloth. Avoid abrasive cleaners or solvents.
• Periodic Checks: Every few months, check all screws and bolts to ensure they are securely tightened. Verify that the mount moves smoothly and without excessive play.
• Lubrication: If movement becomes stiff, a small amount of silicone-based lubricant can be applied to the articulating joints.

Troubleshooting

Specifications

• Brand: SATMAXIMUM
• Model: B07DH9TPZ8
• Mounting Type: Wall Mount
• Movement Type: Articulating, Swivel, Tilt
• Compatible TV Sizes: 32" - 47"
• Max Load Capacity: 35 Kg (77 lbs)
• Wall Distance: 2.6" - 16.7"
• VESA Compatibility: 100x100mm to 400x400mm
• Adjustable Tilt Angle: ±15°
• Material: Durable Steel

Warranty and Support

For warranty information, technical support, or to report missing/damaged parts, please contact SATMAXIMUM customer service. Refer to your purchase documentation or the official SATMAXIMUM website for contact details.

SATMAXIMUM is committed to providing high-quality products and expert support to ensure your satisfaction.

You can visit the SATMAXIMUM Store on Amazon for more information about the brand and other products.