PROCET Gigabit PoE Injector PT-PSE106GW User Manual

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the PROCET Gigabit PoE Injector, model PT-PSE106GW. This device is designed to supply power and data to Power over Ethernet (PoE) compatible devices, such as PTZ webcams, IP cameras, and wireless access points, over a single Ethernet cable. It supports Gigabit network speeds and is compliant with IEEE802.3af, IEEE802.3at, and PoE++ standards, delivering up to 60W of power.

2. Safety Information

• Ensure the power source voltage matches the device's requirements.
• Do not expose the device to water or excessive humidity.
• Avoid placing the device near heat sources or in direct sunlight.
• Use only the provided power cord and accessories.
• Do not attempt to open or repair the device. Refer servicing to qualified personnel.
• Ensure proper grounding for safe operation.

3. Package Contents

Verify that all items are present in the package:

• PROCET Gigabit PoE Injector (PT-PSE106GW)
• Power Cord
• Instruction Manual

Image 3.1: PROCET Gigabit PoE Injector PT-PSE106GW and included power cord.

4. Product Overview

The PT-PSE106GW is a single-port PoE injector designed for reliable power and data transmission. It features two RJ45 ports (LAN and PoE), LED indicators for power and active status, and a standard AC power input.

Image 4.1: Front and rear view of the PoE Injector with labeled ports. The front shows LAN and PoE ports, and LED indicators for Power and Active. The rear shows the 110-240V AC Power Input.

4.1. Features

• PoE++ Injector: Delivers up to 60W (55V 1.1A) of power.
• Gigabit Speed: Supports 10/100/1000Mbps network connectivity.
• Standard Compliance: IEEE802.3af/at/PoE++ compliant.
• Device Protection: Built-in detecting chip prevents damage to non-PoE devices.
• Applications: Suitable for PTZ webcams, IP cameras, wireless APs, door locks, displays, POS systems, and information kiosks.

4.2. LED Indicators

• Power LED: Indicates the power status of the injector.
• Active LED: Indicates active data and power connection to the PoE device.

5. Setup and Installation

Follow these steps to install and connect your PoE Injector:

1. Connect to Network: Connect an Ethernet cable from your network switch or router to the LAN port on the PoE Injector.
   

   Image 5.1: Connection diagram illustrating the LAN port connection to a network switch/router.

2. Connect to PoE Device: Connect another Ethernet cable from the PoE port on the injector to your PoE-compatible device (e.g., IP camera, wireless AP). This cable will carry both data and power.
   

   Image 5.2: Connection diagram illustrating the PoE port connection to an IP camera, Wireless AP, or Video Doorbell.
3. Power On: Plug the provided power cord into the AC input of the PoE Injector, then plug the other end into a local power outlet. The Power LED on the injector should illuminate.

   Video 5.1: Demonstration of connecting the LAN and PoE cables, and then plugging in the power cord to activate the injector. The Power and Active LEDs illuminate upon successful connection.

4. Verify Connection: Once the PoE device is connected and powered, the Active LED on the injector should also illuminate, indicating a successful data and power link.

5.1. Wall Mounting

The injector includes mounting tabs for wall installation:

• Identify a suitable mounting location.
• Use appropriate screws (not included) to secure the mounting tabs to the wall.
• Ensure the device is securely fastened before connecting cables.

Image 5.3: The PoE Injector displaying its mounting tabs for wall installation, along with its dimensions and weight.

6. Operation

Once properly installed, the PROCET PT-PSE106GW operates automatically. It detects the connected PoE device and supplies the necessary power according to IEEE802.3af/at/PoE++ standards. Data transmission occurs simultaneously over the same Ethernet cable.

6.1. Power Output Compatibility

The injector supports various power levels for different PoE standards:

Image 6.1: A chart illustrating the wattage compatibility of different PoE standards (802.3af, 802.3at, 802.3bt) with various devices such as IP cameras, IP phones, routers, 11ac Wi-Fi APs, PTZ cameras, door phones, POS systems, healthcare devices, kiosks, laptops, digital signage, PoE smart TVs, and LED lighting.

7. Maintenance

• Keep the device clean and free from dust. Use a soft, dry cloth for cleaning.
• Ensure adequate ventilation around the device to prevent overheating.
• Regularly check cable connections for secure fit.

8. Troubleshooting

9. Specifications

10. Warranty and Support

For warranty information and technical support, please refer to the official PROCET PoE System website or contact their customer service. Keep your purchase receipt for warranty claims.

Manufacturer: Beijing Creative Lianjie Network Technology Co.,Ltd